Results 1 to 6 of 6
  1. 06-11-2010, 10:47 AM #1
    AdrianJ
    AdrianJ is offline Junior Member
    Join Date
    Dec 2007
    Posts
    9

    Default Selectset 7000: Error 31

    Currently a Selectset 7000 that I'm working on had a NVRAM problem. Resetting the machine seems to work.
    However on Loading of Film into the Selectset an Error is displayed (Error 31).

    Normal procedure for loading of film is done. Cutter Blade works, but upon sending the command to feed the error shows.

    Could this be because of a defective Optical Sensor on the Punch Assembly?
    Last edited by AdrianJ; 06-11-2010 at 11:12 AM.
    Reply With Quote Reply With Quote
  2. 06-11-2010, 04:11 PM #2
    VladCanada's Avatar
    VladCanada
    VladCanada is offline Senior Member
    Send a message via Skype™ to VladCanada
    Join Date
    Sep 2008
    Location
    Ontario, GTA, Canada
    Posts
    877

    Default

    Error 31- Image buffer sizing: found different amount of memory
    Why do you think that's an NVRAM problem?

    BTW -<<AdrianJ has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her.>>
    Why did you send me PM in that case?

    Anyway you need a real PROFESSIONAL Service or assistance.
    I do not do such a kind of job for free anymore... I'm sorry.
    Last edited by VladCanada; 06-13-2010 at 01:28 PM.
    Reply With Quote Reply With Quote
  3. 06-12-2010, 07:14 PM #3
    spapa's Avatar
    spapa
    spapa is offline Junior Member
    Join Date
    May 2010
    Posts
    22

    Default

    Quote Originally Posted by AdrianJ View Post
    Currently a Selectset 7000 that I'm working on had a NVRAM problem. ...
    Did you replaced NVRAM and restored parameters?
    Reply With Quote Reply With Quote
  4. 06-14-2010, 06:33 AM #4
    AdrianJ
    AdrianJ is offline Junior Member
    Join Date
    Dec 2007
    Posts
    9

    Default

    Yes, I've replaced the NVRAM IC. Display shows it as a punch error... but operator's manual does not have up to error 31. The error looks like a punch error because it has the icon.
    Reply With Quote Reply With Quote
  5. 06-15-2010, 10:19 AM #5
    Hyperbarem
    Hyperbarem is offline Junior Member
    Join Date
    Jun 2010
    Posts
    6

    Question

    Hello AdrianJ

    I have the same error it is a Punch Jam in the output punch assembly, I found some pieces of film stucked in the center punch, I cleaned it and the machine worked fine just once, I have the same error again but now I can´t find nothing, even when I dissassembled the punch mechanism.

    It seems to be a sensor error, or in the worst case, a punch motor failure.

    I'm waiting for a reply from the service personel from Viprofix.

    If you have a solution for that.... please... let me know. ok? If I have the solution, I will let you know.

    Greetings
    Reply With Quote Reply With Quote
  6. 06-15-2010, 11:03 AM #6
    AdrianJ
    AdrianJ is offline Junior Member
    Join Date
    Dec 2007
    Posts
    9

    Default

    I'm not in the location where the machine is.

    But when I go there I'll try running diagnostics on the machine.

    Boot or reboot the unit.
    Hold keys 1 & 4 to get that System DIagnostic Screen.
    Go to Test (Key 3)
    I believe that it either Media Control 1 or Control 2.
    Test the Punch there.
    Reply With Quote Reply With Quote

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Sponsors

Esko Sponsored Content

WhatTheyThink Sites