Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Exclamation Magnus 400 Part No.

    Would anyone happen to know the part number for the distribution board on a Magnus 400 or where I can find it?

  2. #2
    PACH's Avatar
    PACH is offline Senior Member
    Join Date
    Aug 2009
    Posts
    341

    Default

    Quote Originally Posted by MattG View Post
    Would anyone happen to know the part number for the distribution board on a Magnus 400 or where I can find it?
    Hi MattG,

    This is the part number for the Power Distribution Board Assy.: 503-00334D. The number is at the bottom RHS of the board. Can not see it without removing the Interlock board Assy.

  3. #3
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Default

    Thanks Pach for all your help! Another question....do you know where the "Local 3 Board" is? We installed the new distribution board, and it's coming up with and error with that board.

  4. #4
    PACH's Avatar
    PACH is offline Senior Member
    Join Date
    Aug 2009
    Posts
    341

    Default

    Quote Originally Posted by MattG View Post
    Thanks Pach for all your help! Another question....do you know where the "Local 3 Board" is? We installed the new distribution board, and it's coming up with and error with that board.
    Hi Matt,
    If it is a manual plate load M400 than : open the RHS door and drop the metal flap ( 2x thumb screw) and you will see a Metal box upright. Lift back the flap and yo will see 2x allen screws that need undoing. Now open the flap again an ease the metal box ( with the Local board inside it) out from the mother board.
    If your M400 has an Autoloader, than there is another Local3 board in there , again behind the RHS paper dissposal door , behind a metal pannel. Good luck.

  5. #5
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Default

    PACH - It's not recognizing the Local 3 Board. Since we replaced the main distribution board, does the distribution board have to be programmed to recognize the Local 3 Board? When we pull up the Local 3 Board it shows all zeroes.

  6. #6
    PACH's Avatar
    PACH is offline Senior Member
    Join Date
    Aug 2009
    Posts
    341

    Default

    Quote Originally Posted by MattG View Post
    PACH - It's not recognizing the Local 3 Board. Since we replaced the main distribution board, does the distribution board have to be programmed to recognize the Local 3 Board? When we pull up the Local 3 Board it shows all zeroes.
    Do you get any error message when you load the M400 application?

  7. #7
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Default

    It just says that it can't connect to the Local 3 card.

  8. #8
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Default

    The operation "PutandGet" of Local 3 card is what comes up in the error message.

  9. #9
    PACH's Avatar
    PACH is offline Senior Member
    Join Date
    Aug 2009
    Posts
    341

    Default

    Quote Originally Posted by MattG View Post
    The operation "PutandGet" of Local 3 card is what comes up in the error message.
    You did not say if it is a manual plate loading Magnus and also what was the original problem that you had to replace the Distribution Board.

  10. #10
    MattG is offline Junior Member
    Join Date
    Jun 2011
    Posts
    9

    Default

    Hi PACH:

    It is a manual plate loader and we replaced the distribution board because it shorted out when imaging a plate. The part of the board that blew out was the vacuum pump power circuit. It arc'd against the frame.


Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Sponsors

Esko Sponsored Content