Standard Finishing
Xerox4Over

Announcement

Collapse
No announcement yet.

lotem 400 error system (createFile,2)

Collapse
Canon
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • lotem 400 error system (createFile,2)

    Dear All

    I need absolutely your help

    After doing joind Diag, which has correctly done and no problem,
    In the main window, error message appears immediately after lauching LotemGui

    E System error [CreateFile,2]
    E the operation "Put" of Distribution Card" fail
    E Drum Power Switch Failed dueto the problemwith distribution Card
    E MCF Card Startup required
    E ....

    Can you tell me please where is the distribution card? What can I do for solving this matter?

    thanks a lot and wisk your quick reply

  • #2
    Hello

    look like there are diffrents problems with your device

    The distribution board is located at the back of the lotem, you must remove the rear cover and look for the powerbox where some power supply breakers are located.
    under the PDB also is located the drum driver.

    looking the ctp from the back at the right door there is a controller for all software and solenoids .
    when tou launch the ctp controller its loadee into that board.

    Check them all.

    Regards

    Comment


    • #3
      Thanks for replying me.

      So I've just checked all fuse on the distribution board, there is no broken, fuse on the transfo back the powerbox, nothing, the drumdriver is correct, all supply breakers are checked and on. All solenoid door are checked and correct, 5v and 24v 115v - 230v is correct on the distribution board. The buzzer run when one of solenoid door is not opened simultaniously. NUC - STROBE7 and TSP are ok in looking at inside the controller and following the hardware utility. Only distribution card and hardware card are fail and non ressetable causing system error (createFile,2)

      Only, my question is: is it possible that the hardware computer T964S needs to reload bios, in that case, my floppy disk is out of service. It is a lotem 400V FH with omron. I lay this question because all problems are come during and after doing joind diagnostic fail. and after changing battery
      in that case, I need absolutely download BIOS floppy reload.

      Regards.

      Comment


      • #4
        Dear all

        I think my problem come from BIOS which is corrupted, After tested all card, MCF - DDB - NUC - TSP, .. all are correct, only MCF can not load cause of this BIOS error so.
        I try to reinstall my floppy BIOS disk but it is failed.

        Can anyone send me a link to download it please? It is a lotem 400V year 2002, 12 diodes, - Main board card is a TEKNOR TEK T946S 566 -1.

        Regards

        Comment

        CanonKBAAvantiSmartsoft (Presswise)DuploEnfocusXerox4Over

        Canon Embellishment White Paper

        Collapse

        Print Embellishment Goes
        Straight To The Bottom Line

        InfoTrends reported that interviews with more than 100 print customers demonstrated an appetite and willingness to pay premiums of 24% to 89% for special effects, over CMYK-only printing. They also indicated embellishment could apply to a significant portion of their work. Embellishment options can include hot foil stamping, spot gloss UV, embossing, debossing, letterpress, diecut shapes, lamination, duplex, triplex, gold foil, silver foil, copper foil, white foil, black foil, clear foil, etching, and laser cutting techniques. Download The Free White Paper.

        CanonSmartsoft (Presswise)AvantiKBAAvantiEnfocusGraph ExpoDuploXeroxChili publish4Over

        What's Going On

        Collapse

        There are currently 6138 users online. 94 members and 6044 guests.

        Most users ever online was 10,745 at 04:03 PM on 10-10-2019.

        Working...
        X