Standard Finishing
4Over

Announcement

Collapse
No announcement yet.

Dot gain?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Dot gain?

    I need to get better control on dot gain.
    We guess to much...

    Is there a good read on avg. dot gain for sheetfed offset?

    What are most peoples avg. dot gain??

    How I was show was to get film into cal. 30 reads 30, etc.
    Then for dot gain or prod. manager jacks the exp up from 7 to 9. This works most of the time.
    But, a lot of the time stuff looks light. Were not a true 4cp shop. We run on 2 color press w 2 passes.

    I know we can setup profiles, trans curves, etc. This is what I want to do....I'm sick of guessing.
    We need a profile for gloss and offset. I dont want to put trans curves on pics etc. I want a profile setup at the rip so I know when I'm in cal. the rip will handle dot gain. There is a spot in the rip for that.
    Just want to see what other do before I did on my own.
    Were always Soooo busy, we never have time to do shit.
    Please Help!

  • #2
    Re: Dot gain?

    Hi PrepressDog,

    I invite you to take a look at PerfX Press Curves™ tool. It allows to calculate DotGain OR GrayBalance curves for plates, in order to match established standards.
    Very easy to use and pressmen love it!

    http://www.tglc.com/english/PerfX/Press%20Curves.html

    Hope this will help you!

    Comment


    • #3
      Re: Dot gain?

      I would recommend taking a look a the G7 methodology, which is currently adopted by Gracol and SWOP (and soon possibly FIRST for Flexo) which allows for a common tonal respose and gray balance from differing print processes using differeing consumables. Read the G7 "How To" guide and familirize yourself with the concept. Basically you would compensate your Rip output to match the targets for print density or gray balance. Implementation can be done by manual calculation, or by software such as PefX or Idealink Curve.

      Comment


      • #4
        Re: Dot gain?

        Dot gain control is not just only building a curve in the RIP. This is what you do after controlling the variables affecting dot gain. It is hard work and it needs close cooperation between prepress and press but after all you will like the result.

        The following variables have been found to affect dot gain:
        Ink: Tack and Viscosity, Ink / Water Balance, Pigment Strength, Temperature, Ink Film Thickness (Print Density)
        Paper: Brightness, Whiteness, and Opacity, Porosity / Holdout, Smoothness, Web Tension
        Fountain Solution: pH / Conductivity, Hardness of Incoming Water, Type of Dampening System, Formulation
        Blanket: Compressibility, Age, Tension, Surface Characteristics
        Plate Exposure: Processing, Reactions (Age, Light, Chemicals)
        Tension: Rollers Diameter, Settings, Glazing
        Speed: Low / High
        Packing: Over / Under

        It is important to realize that the ink film thickness will have a dramatic affect on Dot Gain. Therefore, it is critical to monitor and control ink the density during a run so that the dot gain is consistent throughout the run.
        The Dot Gain should be rechecked after any variable is changed in the printing process but in general latest every six month

        Comment


        • #5
          Re: Dot gain?

          Hi PrepressDog,

          You might also take a lot at InkReady, which has dot gain compensation features.

          http://www.imposition.com/web/Produc...8/Default.aspx

          This is a full version you can test for 5 days.

          Ray
          Ultimate Technographics

          Comment

          UltimateDuploSmartsoft (Presswise)Standard FinishingKBA4Over
          UltimateDuploStandard FinishingKBAKBA GTIChili publish4Over

          What's Going On

          Collapse

          There are currently 5041 users online. 111 members and 4930 guests.

          Most users ever online was 6,151 at 11:36 AM on 11-17-2017.

          Working...
          X