Standard Finishing
Xerox

Announcement

Collapse
No announcement yet.

Pull up banner (how to make)

Collapse
Canon
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Pull up banner (how to make)

    Hi There. I realize these are fairly simple to put together (I just don't want to cock it up, first time I have done one of these). I have all ready printed a banner on my solvent printer (Mutoh) arppox 2meters x 50cm. I have purchase the stand. I see it uses a double sided tape and locking pin system (brand is "fusion"). Maybe someone can flick me a link. ta Simon

  • #2
    Pretty straight forward. The hardest part is getting it mounted straight so that when it rolls up, it doesn't smash one edge into the side of the stand. Other than that, it should be smooth sailing.

    Comment


    • #3
      thanks kdw,. Was hoping for a youtube clip. I was told you need to apply more 2side tape than it comes with? (not strong enough). Have you found this to be the case?
      I'm guessing different brands will be different. ta Simon

      Comment


      • #4
        Originally posted by BigSi View Post
        thanks kdw,. Was hoping for a youtube clip. I was told you need to apply more 2side tape than it comes with? (not strong enough). Have you found this to be the case?
        I'm guessing different brands will be different. ta Simon
        I've built many of these and as kdw75 says, the most important bit is getting them on straight. Also, take care when taking the tension pin out after assembly, as they are under a lot of tension and can whip out of your hands if not careful, which can cause damage. Never had to add more double sided tape to them.

        Comment


        • #5
          I use the 2 sided tape that comes with it and then for added protection I just take packing tape and run a strip over it. Never had any issues.

          I basically do what this guys does in this video with the exception of the top part, I just put the bar on the edge and let it clamp down.


          Comment


          • #6
            thanks guys! this is all very helpfull. ta Simon

            Comment


            • #7
              Thought it had gone well! until customer came to pick up. Pulled up to proudly show the finished product only to discover this on the edge!!!. I guess I have made a fraction to wide?. It looked like the correct width. Damage is almost 1/2 way up from the bottom just on the left hand side. I could understand it if it did it the first time I pulled it up but worked quite well for 3/4 times before this happened. Your thoughts please.
              Attached Files
              Last edited by BigSi; 08-08-2019, 06:51 PM.

              Comment


              • #8
                I have found the pull up banners we use to be reasonably forgiving. Did you use a template made for your hardware? I got templates for the different pull up stands we use and just follow them, never have an issue.

                Comment


                • #9
                  thanks "wonderings" I have asked the supplier for a template (no luck) Is this case it is suppose to be a standard 2000mm x 850mm pullup. I'll do the remake a little narrower but I should not have to. thanks

                  Comment


                  • #10
                    If it is crooked it can rub against the side and not roll up properly. I always follow it down when pulling the pin out and make sure everything looks ok.

                    Comment


                    • #11
                      Thanks Woundering, I have made again and it seems ok. I have come to the conclusion it was a dodgy unit from the supplier. thanks

                      Comment


                      • #12
                        Hey BigSi, give The Exhibitors Handbook a try for templates. They've got a wide variety downloadable and sorted by brand/model. I've used them quite a lot in the past.

                        https://www.theexhibitorshandbook.co...phic-templates

                        Comment


                        • #13
                          Thanks Harry. Will have a look. ta Simon

                          Comment


                          • #14
                            Re: Pull up banner. Hi there, Does anyone have a template for the brand "Fusion" and size in metric would be handy (I can convert if need to). 850mm x 2000mm. ta Simon.

                            Comment

                            CanonKBAAvantiSmartsoft (Presswise)DuploEnfocusXerox

                            Free Download

                            Collapse

                            Trade Show Survey=
                            Instant October Trade Show Survey
                            Come On! Only 5 Questions

                            PRINT 19 and PRINTING United are squaring off in October.
                            Will you be at one of them?
                            Both? Neither?
                            Please take our 1-Minute survey to tell us about your plans for the two big fall shows!

                            Take The Survey.

                            CanonSmartsoft (Presswise)AvantiGraph ExpoKBAAvantiEnfocusGraph ExpoDuploXerox

                            What's Going On

                            Collapse

                            There are currently 3340 users online. 49 members and 3291 guests.

                            Most users ever online was 6,855 at 12:33 PM on 06-06-2019.

                            Working...
                            X