Recent content by Adnan

  1. Adnan

    Screen Cezanne Image corruption

    Hello All, we are facing a problem with Screen Cezanne, while scanning the image the output is corrupted as shown in the attached pictures. Please advise what is the reason and how it can be resolve. Regards, Adnan
  2. Adnan

    Trendsetter 800II Error 35780

    We have re upload the PDB firmwares but problem remains. only change a little bit behavour that now first time machine boots fine but after few minutes relays fliker and power supplies gets off with error *** Unsolicited Message 35780 Warning [Product:Carriage Presence Fault: Carriage motor...
  3. Adnan

    Trendsetter 800II Error 35780

    Nemo, The problem is that machine didnt give me a time to restore PDB firmware, it went restart in about few minutes and some times run bit long but we can not restore in this situation..
  4. Adnan

    Trendsetter 800II Error 35780

    Dear LoWang, I have try to enter but it gave following error, [MCE] sio con 10 f 11Jun13 17:53:02.453: <MCE> TS>> sio con 10 f 11Jun13 17:53:02.593: <MCE> Connecting to Remote Board Id: 0010 (use ^Z or Esc to exit)SCON Board Id: 0010 is not responding. Operation cancelled. f 11Jun13...
  5. Adnan

    Trendsetter 800II Error 35780

    Yes we have done reset button task and also we have checked all power supplies which are working fine not any change after reset
  6. Adnan

    Trendsetter 800II Error 35780

    we are facing a problem with TS800II. during production an error popup on printconsole screen and machine stop imaging " Carriage Amplifier Fault: +/-12V or 48V supply faulted or safety loop broken Prompt:43312" and after restart of machine we got "System Presence Fault: Satellite Board 24 volt...
  7. Adnan

    Lines on output after 50% Screen

    Hi all, I am facing a problem with Avantra 44, after 50% of screen some lines appear in slow scan direction and if I increase density or LPI then lines become very prominent.... kindly advice.
  8. Adnan

    Selectset 7000 no initialize

    hi Vlad, yes, exactly same problem I faced in about year 2005, when I turned on the machine, only “diag xxx etc.” message appeared then screen went blank, finally I replaced “Dallas” chip and problem solved. you are right, they mention this in manual that’s why i first replaced that 2 ROM’s...
  9. Adnan

    Preps kodak creo training

    Hi Trimmer, you can find all preps training stuff from here, even you can find some activity files, web based traing and Preps PDF training manual which will help you to learn preps your self. https://ecentral.kodak.com/eCentral/Self_support/product_support_results.asp
  10. Adnan

    Selectset 7000 no initialize

    i have experienced that SS7000 boot problem is related with NVRAM and i have replace DALLAS from local market but didnt get success, finally i ordered same chip to agfa and after replacement machine works fine.
  11. Adnan

    Selectset 7000 no initialize

    this problem is related with NVRAM, please check your NVRAM is properly mounted on Mother Board
  12. Adnan

    Signasetter "Error 0931"

    Hi, i am facing a problem with signasetter pro, during boot an error message appear "0931” “Recorder hardware error, check the cabling to the mirror motor and the XY-Control.” I have checked all the connectors b/w XY controller and mirror motor, all are attached properly but error remain...
  13. Adnan

    Agfa Selectset 7000

    hi, i think these types of stalling, lines in copy can be cause by carriage movement problem, i suggest you to please check your carriage movement by gently slide the carriage assembly back & forth and hear the noise & friction, if you find problem then perform carriage rail cleaning/lubricating...
  14. Adnan

    Error 09 on Avantra44S

    Thanx... My problem has been solved Thanx... My problem has been solved Thanx guy's, i have solve the problem....
  15. Adnan

    Error 09 on Avantra44S

    I am facing a problem with Avantra 44S, during bootup on screen shows an error "09", this code is not listed in the manual, i have perform all the tests (Dec, SDM and CSDM) with result passed and also replace the Dec board but error remains, would anyone have any experience with this or know the...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top