Recent content by adub

  1. A

    KM C8000 Bent Corners and Jamming Exiting Fuser

    Just a thought, How much gripper do you have on the actual printed sheet? If you have a lot of ink coverage close the edge it can cause problems on thin stock. Try running with at least .25” margin.
  2. A

    Scanning on Versant 280

    If you don't see a usb slot on the front of the machine, pry off a little door on the front of the machine, should be a usb slot there. Plug in a usb drive, then choose scan on the display of the machine and you can save it to the Usb. No networking, fiery, or software required.
  3. A

    what is this kind of padding called?

    Does anyone know what this kind of padding is called? Or what is involved to make it. This particular one has a hexagon finish to it, but I have another one that looks more like linen. It is much stronger than regular padding glue and flexes more like a perfect bind glue.
  4. A

    Looking into Presscentric for our printshop to replace my Orderdesk. Anybody have a opinion?

    We’ve been using them for a few years, so you have any specific questions?
  5. A

    Need Help Adding Quicksetter Printer to Mac

    Why don’t you export your file as a pdf, you should be able to import that file directly into the rip to make the plate. This bypasses having to setup the rip as a printer. Much easier.
  6. A

    HELP!! Printing 18pt C2S Tango on Ricoh 9210

    my guess is something is messed up in your profile. Does it print fine on 12 or 16pt? Try using that profile, or start a new one from scratch without using the media import and see if that works
  7. A

    Heidelberg print master Press + Platemaker for sale

    We have a heidelberg Printmaster 46-2 for sale + Mitsubishi SDP-Eco 1630 IIIR – Platesetting System w Harlequin Rip. + Press Specialties C9000 Envelope Feeder + Conveyor + challenge jf paper drill Good working condition. $4000 takes it all. Located in Los Angeles.
  8. A

    PM 46 air pressure error

    I had a very similar issue about two years ago. I think ours ended up being on the non operator side there are a bunch of small air hoses near the top that actuate the rollers. Take that panel off and see if you can feel any air leaking over there. Also check that you are not leaking anything...
  9. A

    Mylar tabs on Ricoh 9200 /7200

    Yes, they are docucopy with the trilar coating. I did try adjusting the trailing edge transfer, didn't help. When they work the copy is razor sharp and fusing well, but a fair number of them have major flaws that make the set un sellable. It seems like an issue in toner transfer to the sheet...
  10. A

    Mylar tabs on Ricoh 9200 /7200

    Is anyone able to print on Mylar tabs on their Ricoh 9200 or 7200? We can get them to feed fine but the type looks terrible on 15-20% of them towards the edge of the tab, bleeding Flaws that move around, not in the same tab every time. Using the trilar tab profile imported from the library. We...
  11. A

    Lamination cleaning rollers and Ezy taper any good?

    For the hot lam get an adhesive eraser xyron makes a cheap one and a lot is elbow grease will clean it right up. Let it warm up a little but not hot will also help. A rag and solvent also does it but a lot more work.
  12. A

    Mitsubishi SDP-Eco163IIIR Platesetter

    I have one, works great, very few problems. WAY better than trying to do those laser plates, especially if you need good looking screens or longer runs.
  13. A

    Challenge drill press issue

    Make sure the hollow center of the drill is clear, if not clean it out with a nail and also replace the round wood block you drill into. If all else fails put a few pieces of chip board under your job.
  14. A

    3rd party Ricoh 9200

    Has anyone purchased a Ricoh from cbe or impact in Los angles? I like the product but am weary of their service claims vs Ricoh direct.

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top