Recent content by Les Zmyslowski

  1. L

    Kodak trendsetter vlf laser safety loop error!

    Florsa, Primarily safety loop protects machine operator from IR radiation and mechanical hazards. Every operator associates it with open panels. But safety loop also protects the machine from working in inadequate conditions. Safety loop is sophisticated subroutine based on number of sensors...
  2. L

    need a technician for Kodak Magnus 400 II MCU

    Please contact: Les Zmyslowski Service Manager Apresys, Inc. Chicago, IL 60641 TEL:(773)545-7700 Toll Free:(800)899-8111 USA Fax:(773)685-9229 Web Site: http://www.viprofix.com E-mail: [email protected] ************************************************************************
  3. L

    Agfa avantra 44s 168 error code at start up

    Intermittent problems are related often to improper ambient conditions. Make sure Avantra works within its specifications for the temperature and the humidity. In some buildings poor power grounding may result in unstable machine behavior also. Consult your electrician and do the measurements...
  4. L

    Lotem Drum Housing Material

    The Lotem 800 drum and carriage base is made of 7075 grade aluminium alloy.
  5. L

    Kodak Quantum III 400_Problem

    Dear Zamir, Lotem Quantum edge detection mechanism use its mainly thermal laser head. Focusing laser sends beam into the drum. If the beam points on the drum area not covered by the plate, it falls into the edge detection notch and is deflected aside. When beam points the plate area, it is...
  6. L

    Kodak Magnus 400 Quantum installation

    Lolchris, I have installed Kodak equipment in Africa. I know what is needed for Magnus 400 in your conditions. Please send me an call or email me to [email protected] . Thanks, Les Zmyslowski Viprofix, Chicago IL Phone: +1-773-545-7700 Email: [email protected] Website: www.viprofix.com
  7. L

    Brisque 5 errors

    The reasonable solution would be installing bigger or second hard drive.
  8. L

    CTP Error

    Bruno, Some conditions may be on the end range of acceptable conditions. Some semiconductors may develop sensitivity to ambient conditions or both. In general DTD errors are generated by laser thermal head internals most of the time. Remote diagnostic is the way to sort things out. From...
  9. L

    Lotem 800V Noisy Fan

    Fans are rather blowers. Access is via left plastic service door. Next hinged laser box must be opened outwards. On the box top are rectangle metal plates. Behind plates are blowers. Blower rotors use bearings. Lubrication does usually work.
  10. L

    Magnus 400 - How to open Rear Door when power supply fails?

    Magnus 400 doors have interlocks cutting off the power. Opening covers on any CTP machines poses risk of radiation. The danger is greater with thermal lasers because radiation is invisible. Protective eye-ware is a must while bypassing the interlocks. Call me for machine specifics 773 545 7700.
  11. L

    Magnus 400E solid lines from laser 11

    Please call me for the solution. Les Zmyslowski Service Manager Apresys, Inc. 3650 N. Cicero Ave. Chicago, IL 60641 TEL:(773)545-7700
  12. L

    Lotem 400 Exposing problem

    Massive diode problems in Lotem 400 may be related to inappropriate working conditions. Lotem optimal work temperature is 25 Celsius ( 77 Fahrenheit ). Relative humidity 55% non condensing. I would check if laser cooling fans are working OK and if air filters are not clogged with dust.
  13. L

    lotem 400 no error appeared , but nothing exposed

    There are many possible issues, but generally it should be something very basic. The most efficient way to sort thing out is conversation. Please call me at 773 545 7700.
  14. L

    Lotem 400Q Preventative Maintenance

    LOTEM 400 Lotem 400 Quantum PM ----------------------------------------------------- Loading system cleanig Lubrication of swivel Cleaning fans Vaccum system maintenace Laser optics cleaning Cleaning the drum vaccum holes Edge detection strip cleaning Cleaning sensors and detectors V-block...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top