Recent content by moradnet

  1. M

    MAGNUS 400 Detect Plate Edge Problem

    Thank you PACH I will contact kodak support for replace laser 29
  2. M

    MAGNUS 400 Detect Plate Edge Problem

    Thank you papamoose.. Yes the Laser Number #29 is Failed during Calibrating from 115mw to 300mw value, also I tried putting the plate in the other way round but the Plate edge detection problem still found. Is there a way to solve the problem of laser No. 29 by Laser calibration or CTP...
  3. M

    MAGNUS 400 Detect Plate Edge Problem

    Thank you for your reply, Magnus 400S, The type of plates Thermal TP-II ,Positive ( from HUAGUANG Co.), we using several sizes of plates for (GTO52, Speedmaster52, Printmaster74). Some times I get an error message "Failed to detect Plate Edge", but most times the Laser Head takes long time to...
  4. M

    MAGNUS 400 Detect Plate Edge Problem

    thanks for all excellence members in this wonderful forum, especially the members who are doing time in providing assistance and information to benefit everyone .. I have a MAGNUS 400 CTP manual feed, The problem on the Plate Edge detector it is requires a long time for get the edge of the...
  5. M

    AccuSet1000 With Viper1.9 Rip Active 0C problem

    I have Service manual for all agfa systems, but no any info for electronic errors and Apis Boards, About the Apis Board, I did replace all chips and 75als ICs, but the problem still found, I believe that the AMCC PCI chip lead lo this problem. this part is not found in local shops. Thank you..
  6. M

    AccuSet1000 With Viper1.9 Rip Active 0C problem

    Hi VladCanada, Thank you for you reply.. Only I need to know.. what is the parts on Board it cause broken channel problem , 75als192 or 75als197? In local spare parts shops found 75als192, 75als193 big size. Also inform me are the 75als193 equivalent 75als197? Thank you..
  7. M

    AccuSet1000 With Viper1.9 Rip Active 0C problem

    Hi I tested the Board on PC using Unidiag, the Program successfully get Accuset parameters, and can change Imagesetter parameters, but during try to send AgfaTest.TIF to imagesetter the Imaging window on Unidiag appear imaged status account 0%.1%.2%........100% quickly,after that Unidiag hung...
  8. M

    AccuSet1000 With Viper1.9 Rip Active 0C problem

    Hi Kindly..Please Help me for repair APIS Board, I was replaced all chips FIFO, Uc, STATE,APIS Chip, and NVRAM, from other good Board, but the problem still found.. Test using Viper Rip 1.9 and Accust1000 results: The Rip high speed send the job to Imagesetter only show in status bar...
  9. M

    AccuSet1000 With Viper1.9 Rip Active 0C problem

    I have problem with Agfa Accuset1000, during send the job from TCP-IP or Hot Folder *.ts the Rip start buffering the Job and start sending it with high speed to Imagesetter the Rip counter start from 0 to 100% after that Rip Hang!, during that Imagesetter control pannel appear "Rip Active 0C"...
  10. M

    Need help for Avantra30 problem

    Thank you very much.. The problem is IC No.# 75als192.. I Replace it and Test...OK :)
  11. M

    Need help for Avantra30 problem

    Thank you mr. w3112 for your info, I did use other Rip with new APIS cable but the problem still found.! thanks
  12. M

    Need help for Avantra30 problem

    Dear Mr. Mr.VladCanada I need your advice.. Thanks..
  13. M

    Need help for Avantra30 problem

    HI , I am sorry I did forget this note in first post: The result of solid 100% contain white horizontal lines,Attach sample of problem. I did replace 3 chips 75ALS193 and one chip 75ALS192 all this chips found up side from APIS port on DEC according to Advice from Mr.VladCanada and Mr.Anayma...
  14. M

    Need help for Avantra30 problem

    Thanks for all.. The machine test 4dpi result ok no problem. but any job from Rip (Xitron Rip) happen this problem.! I did try to use Agfa Apogee PDF Rip with new APIS cable but the problem also still found. Imagesetter info: Agfa Avantra30 with OLP, Xitron Rip0.7 Kindly I will wait for any...
  15. M

    Need help for Avantra30 problem

    Thanks for own of this forum and all members.. I have Agfa Avantra30 Imagesetter.. during last year good working with out any problems, but on this week found problem on the dot screen appears white lines on the middle of dots !..:( I checked the carriage and spin motor but all ok, also...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top