Recent content by Tony Blanco

  1. T

    ERROR E4e24 on PTR 8600. Sensor for LD block.

    Hi Shfierce. Thanks for answering. Yes, I fixed this problem doing as follows. I turned off the CTP and the I moved the recorder head manually to the home position, then I turned on the machine and it worked until now. I also received help from Ali, who is always helping me about this CTP on...
  2. T

    ERROR E4e24 on PTR 8600. Sensor for LD block.

    Hello all. I would like someone help me with this issue. I have a PTR8600 which, while it is starting, presents this error: E4e24: Sensor for LD block has not been connected. I would like to know what sensor is it, on the othe hand, if someone has suggestions, please, let me know. Thanks in...
  3. T

    Screen PTR 4300 MAL problems, it doesn't recognize when there's no plates.

    Hello All I would like you to help me with this issue. I have a little problem with the MAL (cassette unit) of a PTR 4300S. It seems everything works fine, but this MAL doesn't recognize when there's no plates on it. When this MAL finally loaded all the plates, and it tries to find for another...
  4. T

    error screen 8000

    Thanks all. It was necessary to replace two diodes and write again all the diodes values, because this machine lost them. Thanks!!! Tony
  5. T

    Screen PTR4300S punch unit problem

    Thanks Aligh for answering. You are right, the problem was, one of the gear that leads the chain of the transport was broken, it didn't allow the plate to rewards right and it produced the error. I replaced this gear and the problem was fixed. Thanks a lot. Tony
  6. T

    Screen PTR4300S punch unit problem

    Also I exchanged the sensor PH63, but it didn't fix the problem. If I perform a Centering Test, the problem is fixed for one day, but after starting the machine in the morning the problems appears again. Thanks. Tony
  7. T

    Screen PTR4300S punch unit problem

    Hello all. I would like you to help me with this issue. I have a Screen PTR4300S which after punching the plate, the plate rewards, close the shooter and then open and close the shooter again and then, the path raises with the following error. E5130. Plate does not leave the punch unit. I...
  8. T

    Looking for an Interface Cable for DotMate 7500P

    Hello all. I would like you to help me with this issue. I am looking for the Differencial SCSI interface cable for a DotMate 7500P P/N: 9601300850 SCSI cable, Differential, 50 - 68 pins, 5m I am located in Costa Rica, Centralamerica. Thanks in advance. Tony Blanco
  9. T

    Screen PT-R4300S Error. E41f4: Servo Pack is illegal

    Finally I resolved the problem. I tested another ServoPack Box and the issue was fixed. It's suppose a 50Ω resistor controls the braking system, but the resistor is good. For that reason, I decided to exchanged the ServoPack and the problem was fixed.
  10. T

    Screen PT-R4300S Error. E41f4: Servo Pack is illegal

    Hello all. I would like you to help me with this issue. When I try to print at 1000RPM the CTP load the plate normally, then it performs the measurement, but when it starts to print the drum run normal but few seconds later it descends the speed and presets this error: E41f4: Servo Pack is...
  11. T

    error screen 8000

    Raymond, thanks for answering. Not yet, the machine continues bad. On the other hand, the red light of the Power Supply in on when I bypass the interlock, but if I connect the cable that comes from the Head Board to Power Supply in the right way, the red light doesn't go on. It only starts the...
  12. T

    error screen 8000

    Hello Screenhk This error is called E4ef6: Exposure Head Error. A command was sent to exposure head. But no answer is turned from the exposure head. Juanjo changed the Head Board, changed the relay which is installed on Backplane and check the Power Supply, but the problem persists. The -5v...
  13. T

    light intensity adjustement error 0ch

    It's possible that you have one or two laser diodes damaged, when it occurs, the Screen can continue operating but it cannot calibrate the power. Your machine is a 32 diodes one, it measures the target power using all the diodes light. Try cleaning the calibrator sensor and the lense of the...
  14. T

    PTR 8600 (Fuji T9000) electric board problem

    Anastasia. Excuse me for delaying but I don't have yet all the information, I am looking for. This card is called 64LD-CPU2 and it's located on the Recording Head Unit. The part number of Screen is S100006570V00 and it's name is PCB 64LD_CPU2. It is controlled by a PowerSupply called...
  15. T

    Agfa Acento S doesn't upload form L-100 MAL Cassette

    Thanks Farshad. Finally I fixed the problem performing this procedure and changing the H-1 value from 71 (original value) to 53 and the plate path starts to load the plates. I think it's possible ( I'm not sure) the vacuum pump lost some amount of pressure for the lifetime, and it was necessary...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top