Search results

After printing 250 sheets of 250gsm Xerox Matt on our Xerox 700, we sent the sheets round to our finishing house for Gloss Lamination and were told by them that they were having problems with D&K SuperStick Lamination sticking to the paper and that they were also having this problem with another...

One of the annoying problems with printing to my Xerox 700 from my Creo RIP is that, when imposing a job and printing with cutmarks turned on, they are so close together that when I am printing 2 sided, I have to make sure that my backup is near perfect otherwise the marks will show on one of...

Thank X33, I will give that a go and see what happens. I've never had this problem before. I went through some file copies of previous work and found that when using the same calibration for covers & inner (280gsm/170gsm), they were very close in colour, so I don't know if it's only this...

Thanks for all your replies, I have carefully read each one of them. I've been used Xerox presses for about 8 years now and have quite a lot of experience in colour correcting, but it's always good to find out how others are doing it as well, and so, would never say that my way is the correct...

Since I wrote this post (back in July) I have had the same problem about 2-3 times and straight away, I open the top covers and blow some air onto the 2 sets of sensors next to the rollers using the small tube supplied to get into the nooks and crannies. This clears the error straight away...

What I am doing is loading 280gsm Xerox Matt opening the paper tray, choosing 257-300gsm Coated setting, closing the tray and printing 10 copies, then I open the tray and close it again (still with 280gsm Xerox Matt loaded, when prompted, I choose 151-176gsm Coated and printed exactly the same...

Just found out what was happening...there was paper dust on the sensors. I sprayed compressed air from a can of aerosol to clear the dust and it's working perfectly.

I'm printing a 24pp A4 book and noticed a huge different in colour when printing the cover (Xerox 280gsm Matt) and the inner pages (Xerox 170gsm Matt). These is a light blue bar which runs across the double page spread and it looks much darker on the heavier stock. If I run the 280gsm Board on...

Does anyone know how I can insert a slip sheet at the end of a job rather than between each set. Or, does anybody know of a work-around which means I don't have to go to the machine and insert a sheet after each PDF. Reason: On a regular basis, I have to print about 4 Packs a day consisting of...

Soon, I will be Digitally Printing a 4pp Business Card on a 350gsm Matt. It will then be Matt Laminated both sides, scored on my Morgana Digifold and folded. Are there any solutions to keeping the Business Card folded AND flat, because I'm sure that the board will keep popping open. I was also...

An error has come up on my Morgana Digifold which says 'Clip P'. I looking in the manual and it said there was a paper jam. I then cleared all paper jams from all areas (including removing the back) and it kept on coming up with the same error. I have also used a can of compressed air and...

I've been using Xerox Digital Presses machines since 2003 and know the 2045 and 5252 inside out. I'm now getting to know the Xerox 700 but have had so few problems, that I'm wondering what can possibly go wrong with it. The only way I will know is when a problem occurs, which is typically in the...

Does anybody have/know of a PDF file which contains ALL Error Fault Codes for the Xerox 700. The Xerox 700 User Guide mentions some of them but then, there are huge gaps between Error Code Number which seem to be missing

Xerox DC 2045 Paper Jam 100 gsm -135 If this is only happening on A4 (Not A3/SRA3), then try and fee the paper the other way around (Short edge fee instead of long edge fee)