Search results

that would be too easy tech doc nothing has been that easy so far the home made cable was a test to see if the original was the problem i never did find the specifications for the cable so i may have just copied the problem to the new cable the only way to know for sure is to buy a new cable...

thanks Vlad that might be a bit tricky i don't know anyone with a spare PAC board i might have to start a thread to ask if someone knows someone in Brisbane that can help is there a service manual for them or any tests that can be done to diagnose any problems i mean if i gave to board to an...

Hi this is a continuation of this thread http://printplanet.com/forums/agfa-systems/22350-accuset-800-job-time-outs I have reinstall the PAC pci card, RIP software and drivers i have made a new cable using the pin out in the attachment which i copied from the old cable and I'm not sure if its...

not sure how i can help i don't know much about this rip you should start a new thread in agfa systems titled something like "configuring apogee taipan 3.1" or "help with taipan 3.1" I'm sure someone can help

i didn't use that sort of connector because i didn't think i could press it well enough with out the proper crimper didn't think of using a vice that would have been easy but i couldn't get a short length of 40way ribbon so i went with a solder d37 and d62 with a 1 to 1 i tested it with the...

hi i got what i needed for a new cable and put it together with a 1 to 1 pin-out and now the apis driver wont start but it will with the old cable so the the pins are obviously wrong dose anybody know what the correct pin-out is for the d37 plug on the accuset to the d62 plug on the pac board...

Thanks for all your help everyone its been a great response right now I'm trying to organise a new cable and hopefully that will fix my problem i have to order what i need from over seas so its might take a while but i will let you all know how it turns if it works i will reply to this thread...

Hi Guys when I shut down I turned of the image setter and rip pc today I tried to check the cable but couldn't do much so I plugged it all back in sent a file it timed out so I jiggled the cable and held it straight out the back of the pc and the next file worked fine I'm going to try and get...

Hi Guys I checked the fuses and they were good I unplugged the cable plugged it back in made sure it was all tight I sent a small file through the tcp/ip channel and it worked fine I sent a different one through the pipe from the front end and it worked fine shut it all down came back an hour...

Hi this is a continuation on a previous thread "help with accuset 800" The rip I’m using is apogee s2v2 up6 on w2k I am still getting job time outs with this message in the pilot imaging window 05/06/2010 10:31:15 AM - No on-line processor present 05/06/2010 10:31:15 AM - Connected to engine...

I’m trying to run an Accuset 800 with a windows 200 system using apogee pdf rip s2 v2 I checked the apis interface card and it looks like whoever build the computer didn’t put risers behind the mother board so no pci cards can ever be pushed in far enough I’m hoping that when I recently moved...

Thanks Vlad i found f1 and f2 but i couldn't find f3 they are small clear cylinders sticking out from the main board just under and to the side of the apis ribbon cable plug i couldn't get them out i didn't want to twist or pull to hard on them how do they come out

Hi can anybody help me with this accuset i'm trying to print film and the jobs just time out and i get this message 26/05/2010 07:18:03 PM - Job 'GrouseRecordsFilm.pdf' (205) started 26/05/2010 07:18:03 PM - Page 1 : Plane 'Gray' started 26/05/2010 07:18:05 PM - Page 1 : Plane 'Gray' ended...

if you download and install this FTP client FileZilla - The free FTP solution you can download the files from my FTP server let me know when you are ready and I will send you the address

Dose anybody know anything about the AGFA DryStar 5500 its a medical imager but i was wondering it could be used to print graphics

Thanks for everything guys I hope the ftp upload wasn't to slow for you :D

Thanks Daniel you help here is really appreciated I will pm the ftp details

I put a new fuse in tonight and it started I was completely dry the replenish low level warning light was on the dev and fix ones were not I filled the replenish drums up and the warning light stayed on I filled the dev and fix tanks with water and the replenish light went out and it was...

is this fuse protecting the machine from a faulty transformer because there is no power to anything when it is blown where do i find the transformer and how can i test it if it is the transformer would that be a genuine G&J part or could i get a compatible one from any electronics shop

on the side it says Agfaline C the placard at the back looks like this