Search results

  1. M

    EBM 18 - 19 PLC DigiKut Cutter

    I bought this cutter used. It does a decent job for what I need it to do, BUT: 1) the back guage is 5MM off from the display 2) The display is set to MM and I would prefer inches. I have contacted the manufacturer, but they were no help. I'm hoping someone with one of these cutters can help...
  2. M

    Xerox D125 Slow Printing

    Recently my D125 has started doing something strange. The Finisher is cycling (rises and lowers often during a job). The Fix suggested is get a firmware fix (SHA-256). I don't have a service contract with Xerox. Is there a way for me to get this firmware fix?
  3. M

    Xerox D125 Paper Tray Confirmation

    Is there a way to turn off Paper Tray Confirmation of stock? When I run NCR numbered forms, I run one ream at a time. Half the time I forget to hit the confirm button. It would be great if I could turn it off.
  4. M

    Centering image on sheet

    Ok, I'm embarrassed to ask this question (I should know it, but don't). I use InDesign, create a form, 8 1/2" X 11" image, centered, (no bleed). I am printing on a Xerox D125 B&W copier. The printed image is not centered on the sheet. I use the Image Shift to center the image. How do I create a...
  5. M

    Illustrator only has one font "Myriad Pro"

    I don't use Illustrator much, but I just noticed I only have access to Myriad Pro font. Generally I use InDesign, which has a lot of fonts. After reinstall, no change. Any thoughts?
  6. M

    EBM 19 PLC Cutter

    I just downsized. My new place doesn't have room for my old 30.5" Challenge. I bought a used EMB 19 PLC cutter. Does anyone have one? What about a manual? Any experienced help appreciated, Ralph Manassas, VA
  7. M

    Xerox Versant 180 Mystery

    Ok, for all you V180 owners. I am printing a job, single sided, 20# cotton writing stock. Pulling from paper tray 1, stacking on top output tray. If I finish FACE DOWN, I get a dog ear on the leading edge. If I finish FACE UP, no dog ear, runs perfect! Any idea's? (Yes, I ran the job face...
  8. M

    Xerox V180 Windows 10 install gives me the wrong driver

    I have two systems. System A, when I add printer, finds V180 does the install, shows Driver Xerox EX-i 180 Print Server US 1.2. System B (when I do the exact same) shows Driver Microsoft PS Class Driver. I can click on the down arrow and see a list of print drivers. This list shows Xerox EX-i...
  9. M

    Xerox Versant 180 top oversize tray not homing

    I have taken the side panel off. I can see the lower tray homing, but the top tray doesn't home. There are three sensors on the inside back left corner, that correspond with three metal tabs on the tray. Has anyone had this problem? If so, how do you find the bad sensor or do you replace all...
  10. M

    Xerox Centreware setup

    I'm trying to setup my Xerox Versant 180. Some of the configuration settings, seem to be accessed through "Centreware". I have downloaded the setup for it, but I can't get past "Database Server". Anyone who has setup Centreware, can you step me through this?
  11. M

    xerox versant 180 doesn't go into sleep mode

    I have the timers set to 5 minutes, low power mode, then 5 minutes to sleep mode. It never goes into either (as far as I can tell, energy save button never lights). Suggestions?
  12. M

    V180 No communications with Xerox SMart eSolutions server.

    I bought a Xerox Versant 180 at auction. Now I am getting it set up on my network. It has bustled Fiery. How do I turn off the "Xerox SMart eSolutions" messge? Ralph
  13. M

    Xerox Versant 180 Owner

    I recently purchased a Xerox Versant 180 at auction. Everything went together well, except for the bustled Fiery. Mine has a board with two HDMI ports (one marked CK, the other marked YM) (also came with two 20' HDMI cables). I don't see where the HDMI goes to the V180. I am assuming they go...
  14. M

    Printing Word doc on non standard size paper

    Customer brings in a 67 page Word doc. It is composed on 3.5" X 7" page size. They want to make a booklet (7" X 7" flat sheet size, collate, fold, staple, face trim). My printer is Xerox Docucolor 252 with light production finisher. I have done plenty of 8.5" X 11" booklets, but can't figure...
  15. M

    Creating pads

    I am using a Canon 7095 with a EFI Fiery rip. I would like to print 100 pads, 50 sheets each. All sheets are the same. Does anyone know how to do this by sending a single page, X 5000 sheets, inserting a slip sheet every 100? ManassasRalph
  16. M

    Canon IR7105 Carbonless Forms

    I would like to move my Carbonless jobs off my small press and put them on a digital machine. There are several places selling refurbished IR7105's at a reasonable price. Does anyone run Carbonless on their IR7105? How would you rate it (1=jams all the time, 10=runs the same as my press)...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top