Search results

  1. B

    Ptr4300S servo parameters error

    After Initializing the Servo Pack of the ptr4300S to factory defaults, we are getting Encoder Parameters error & overload errors. The machine is working fine. Are there any parameters to adjust to clear the errors. Attached is the pic for the Servo pack status.
  2. B

    Ecrm Stingray 63 Light Stripes

    The Top Cover Interlock has 3 switches. If the cover is not seated properly the laser will turn off, but the system will continue imaging. We wound some scotch tape on the part of the top cover that presses on the switches & we never had this problem again.
  3. B

    Ecrm Stingray 63 Light Stripes

    We are having light stripes around 3mm across the width of the film repeating every 13cm. Cleaned all rollers & SOL sensor. While imaging I noticed the film drive motor with the toothed belt make a pause for a split of a second and continue and repeat the pause every 30 seconds. Could this be...
  4. B

    Image transfer problem from RIP to ECRM Stingray 52/63 Imagesetter.

    Make sure the imagesetter is on Serial mode. Can you see the stingray in the device list on the PC.
  5. B

    Ecrm Image shifting

    Hi Maxon The image is perfect. The shifting is always random & when it is really bad the image starts at 15 to 18cm to the left on a 635mm film. Mostly the shifting is to the left (to the side of the control panel)
  6. B

    Ecrm Image shifting

    Recently our Stingray 63 imagesetter started shifting images to one side of the film. When we output a CMYK separation 63cm wide the Cyan image will image at the centre of the film the Magenta will shift around 1.5inches off center & so on until the image is partially off the media width. We...
  7. B

    PT-R4300S E083f

    E083f :Compressor linked LD have been used for more than the endurance time. We are getting this warning on our pt-r4300S. What does it mean & is there any maintenance we have to perform on the compressor. We have a Vacuum connected to the machine so what is the compressor for?
  8. B

    ptr -4300s error Ex15b

    We are frequently getting error 'Ex15b' Balancer is not moved to target position. Please help with this problem.
  9. B

    Ecrm Stingray 63 loop problem

    When outputting film the Stingray 63 is stuck at "Correcting Media" & stays like that forever. We have to press the stop key on the panel lightly for the job to continue. Once we press the stop key it shows "Creating Loop .... Testing Spinner ..& starts recording. The machine is connected to a...
  10. B

    Ptr 4300S Transfer Path problem

    Thank you Ogin, yavo & aligh. The tension spring on the hime side was broken. Thank you all for responding.
  11. B

    Ptr 4300S Transfer Path problem

    When a plate is loaded on the ptr 4300 the transfer path would go halfway down stop and push the plate into the side alignment bar below the register punch. When the sensors start centering the plate the transfer path would very slowly continue going down, forcing the plate out of the punch bar...
  12. B

    Mako 46 Imaging Solid Black

    We just received a Mako 46 Shipped from Germany (Used) after Installation it outputs solid black area, as if the laser is exposing the entire film. Tried some Calibration Files from Rip, and tried Test Patterns 2 & 3 on the imagesetter with different exposures from 30-150 & the result is Solid...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top