Members

schenkadere's latest activity

S

schenkadere replied to the thread Anyone using Euclidean dot and why? Sheetfed Offset.

You find this to be significantly different than handling a round dot?

May 16, 2022
S

schenkadere replied to the thread Anyone using Euclidean dot and why? Sheetfed Offset.

Lol. I guess so. I can't imagine there's much of that left. I still can't see how that would be advantageous. Maybe to keep the shadows...

May 16, 2022
S

schenkadere reacted to gordo's post in the thread Anyone using Euclidean dot and why? Sheetfed Offset with Like.

Perhaps if you're working with film and process cameras.

May 16, 2022
S

schenkadere reacted to gordo's post in the thread Agfa SolidTune Optimizes Ink Usage for Packaging Printing with Like.

Not to put too fine a point on it... Ink savings is highly image content dependent - and images can vary quite a bit. Also, in my...

May 16, 2022
S

schenkadere replied to the thread Anyone using Euclidean dot and why? Sheetfed Offset.

Gordo, Can you think of a scenario when a euclidean dot would be desired?

May 16, 2022
S

schenkadere replied to the thread Agfa SolidTune Optimizes Ink Usage for Packaging Printing.

Agreed.

May 12, 2022
S

schenkadere reacted to gordo's post in the thread Agfa SolidTune Optimizes Ink Usage for Packaging Printing with Like.

Assuming that it's some form of solid screening (the linked article isn't very clear) - the notion of punching holes in solids to reduce...

May 12, 2022
S

schenkadere replied to the thread Agfa SolidTune Optimizes Ink Usage for Packaging Printing.

Looks like it simply applies a reverse FM dot to solids.

May 12, 2022
S

schenkadere replied to the thread Thin lines appearing on plates.

As suspected, the Fuji tech said it's not the plates...good for me...bad for the pressroom.

May 11, 2022
S

schenkadere reacted to gordo's post in the thread Anyone using Euclidean dot and why? Sheetfed Offset with Like.

I agree. However, if the value is there then the change is justified. Moving from elliptical to round is much less of a change than...

May 6, 2022
S

schenkadere replied to the thread Thin lines appearing on plates.

I don't understand. This was a practice your plant has always done and it just became an issue now? I'm very curious to see if this does...

May 6, 2022
S

schenkadere replied to the thread Anyone using Euclidean dot and why? Sheetfed Offset.

Same here...lol My shop was a former Heidelberg shop so I assume the euclidean thing was a left over from those days. Same as...

May 6, 2022
S

schenkadere reacted to cementary's post in the thread Anyone using Euclidean dot and why? Sheetfed Offset with Like.

same stuff. I've tried very hard to convince my colleagues that we need to switch from elliptical to round, but failed. Then I just...

May 6, 2022
S

schenkadere replied to the thread Anyone using Euclidean dot and why? Sheetfed Offset.

I found switching from euclidean to round was seamless. No noticeable difference in repeat work unless you view with a loupe, lol.

May 6, 2022
S

schenkadere replied to the thread Thin lines appearing on plates.

We are suddenly experiencing the same thing with Fuji LH-PL plates. Oddly for us, it is occurring at more random position on the sheet...

May 5, 2022

Show older items

What About Profitability?

Canon

What about Profitability?
Offset yields new advantages

Read All About It

Members

Top