Search results

There are 3 common issues with the pile height. Around PG B-47 in your parts book (should be pile lever assy) books can vary. #28 (guide piece) can wear / #5.3 (spring dowel(roll pin) can wear, both of these will cause intermittent raising when the feeder gets close to the top/ PG B-1, the first...

Is 15-01 your only error? The boards you replaced? TRM2 & MRK? What year is your press? Where are you located? I have a few tests for you to try if you like. Call me Stan W/ Intermountain Press service,llc. 720-285-9485 PS I also have numerous used parts avail for your Press!

Does anyone have a UFK board (part# 00.785.0189) for a printmaster 46-2?

I don't think you can name a program. It will just assign a program # or you can enter an order #. You can bring up the order or program#. I do have parts of an operator manual if there other information you might need. I specialize on the QM46 but have delt with the Pol66 some. Stan...

Some one was looking for trainning and operational help on SM52. I can't find the post anymore, but I can help! Please send reply or call Stan, IPS.llc. 720-285-9485

you don't want any side to side play on your ink form rollers. This will cause your hangers and latches to wear out. The major causes of your streaks on a QM46 would be rollers maxed out of adj., Ink dist osc drive cams being worn or the roller end play you are talking about. For the end play...

Do you have the operators manual for the press? I could send you the info if you like.

The allen screw adjusts the pressure! Install disc on shaft using set screw in the upper groove. Engauge shaft and set pressure, CW to the imp cyl. NOTE! BE SURE YOU HAVE INSTALLED THE STEEL IMP CYL JACKET FIRST! Do not perf or score on the chromium-plated brass jacket, this can damage the imp...

Give me a quick call, I am going out of town today but I am sure I can help you before I leave. Stan IPS,llc. 720-285-9485

15-01 Is a MRK board (main dr mtr controll board) Does not not usually mean there is a major problem. Just close all other guards, check SF 56 and make sure there are no other errors. Try to crawl press! NO! hand crank press several turns and/or some times shut off and/or unplug press for 1 min...

I am sure I can HELP! Send me your part # and ser #. I have numerous used parts for that machine. If you like give me a call, Stan IPS,llc. 720-285-9485

#3 Printmaster

If the print length is diff, the adj is done at PU-2 plt cyl. Does your PU-2 plt cyl gear O.S. have green grease fittings? They do need grease. If it does not or if it has not been greased, then that is where the gear needs replaced as mentioned by RGPW17100. When you run 8.5X11 20lb, go to SF68...

Hello everyone, My name is Stan. I have my own press service company in Denver (Intremountain Press Service, LLC.) specializing in the QM46/PM46 press line servicing the Intermountain region, or any where else. This all came about in Feb. 2010. I worked for Heidelberg for almost 21 yrs. My...

Just send me your list of Heidelberg part #'s with descriptions. I should be able to figure it out from there. If you have any questions please call me at 720-285-9485 Thanks, Stan

Did you start your company in FEB? Welcome! From Stan with IPS,llc. Denver, Co. One door closes and another one opens. Good luck to both of us in the future. PS. I am parting out a 2001 Printmaster with less than 25ml imp. If you find the need for used parts call me 720-285-9485. The press had...

I have a 2001 QM46-2 with <25ml imp. it has a bad imp & blkt cyl, all other parts are in working condition. send Heid. part #'s for availability & prices to [email protected] or call 720-285-9485

Speed control Speed control Are you still having speed control problems?

Used parts Used parts I should be able to take care of all your needs. e-mail the list w/ phone # to contact you to [email protected]

Proper training is always best. If your operator is experienced in printing small presses, it's just the controls they need to learn. Most older operators are affraid of the eletronics. The younger ones love them. It is a matter of pushing buttons instead of pulling levers. Common blanket is...