Search results

See your email sir I did send you Hope you enjoy it Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: Just give me your email. I have operator manuals for Heidelberg machines Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Thank you sir Blessing [email protected] Mobile+WhatsApp:+505 88611441

Hi sir: This are the possible faulty in his machine Heidelberg SM 74-2 1)Brushless drive-IC (BLA-IC) on HAK defective. 2)Tacho-IC on HAK defective. 3)Failsafe timer has run down and was not retriggered. 4)EPROM on HAK defective. 5)RAM on HAK defective. 6)Motor code could not be...

I have some tech documentation for Polar send me your email Thank you in advance, sincerely Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: I recommend you, to see the operation for Pneumatic Cylinder Y6 in PU1 ,will work like the PU2, see if the mechanism is Good, or loose the pipes or, leak in the cylinder, or dirty in the swin lever, and lack of lube in any chain of movement of autoplate. Hope this is problem using the...

ok, sir Additionally, test the power supply, and look for loose connectors, corroded,dirty, broken wires, and clean every Edge connector from Electronic board( most of 75% of electronic failures) is to due this problem. Let me know.sincerely Blessing [email protected]...

Hi sir: Hope you are well. Please if you are sure the error codes is electrical , please press :Details for to show how is causing this problem o.k? if the screen show to you the Star condition do it: FOR TO RESET The machine.The screen will bring, 3 conditions: 1)ESC 2) START(For to Reset) 3)...

Hi i have some tech documentation for Hamada. Send me your email or send me email Blessing [email protected] Mobile+WhatsApp:+505 8861 144`1

Hi sir: Your comments are NOT clear, if you look your operator manual, has indication , how to installing very securely, and right for his machine. However, you must do it, with Patience, and carefully in order to damage any New Rollers, and observe the indication coming with the Factory like...

Hi i have some tech documentation for Hamada. Send me your email or send me email Blessing [email protected] Mobile+WhatsApp:+505 8861 144`1

Read carefully, they manuals and software Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: Go this website and download: Manuals Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Take care when you are changing the Fuses, with the Same type of fuses. 1) the same Voltages example 120Vac, or 220VAC 2) Same rating of Amps: 3amps, same tipe of Amps, NOT less,!! or more. 3) Turn Off the machine totally, for to avoid electrical discharge. 4) Test after replace, if there...

Hi sir: You can easy test the sensor: get your camera cell phone: with the camera cell look the I.R sensor, if is o.k you must look in the camera of cell On , since the human eye CAN not see the I.R spectrum. 2) if is OFF, there are 2 possibilites a) lack of voltage Vdc in the sensor or loose...

Hi sir: I have some tech documentation for Stahl Roller adjustmen send me the model, and your email, Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: I Have some service manual for Hamada, including the B452 electrical s. m Let me know.or send me or give me your email Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: 1) please before to take out the panel 2) check the FUSE: F5 of 2amp, is located in the Main transformer ETG -103B 3) then test the fuses F1+F2= 1amp 4) F3+f4=2 amp all of them located in the secondary of the main transformer ETG Good luck, let me know any question or tech doc...

Hi sir: Please do the next steps: Cause: The actual position loaded into the control counter when the reference position is passed does not coincide with the reference position stored. The allowance adjusted is also exceeded in this case (default = 0.008 cm). This is caused by the loss of...

ok, test the steps with the Voltage sir The 1 steps: is test the Power supply Low voltage undervoltage 24V, cause can be control voltage too low 19V, Check the power supply vs the schematic diagrams from your TechnoTran HydroSTAR Compact Alpha.d. and Repair. 2) Look for loose connection...