Search results

ok Thank you in advance, sincerely. Blessing [email protected] Mobile+WhatsApp;+505 8861 1441

Hi Sir: Attached you will find a circuit made for my person, as Professional electronic+electrical engineer by over 49years of experienced in many disciplines like Graphic Arts Equipment, Now retired by my age 69 years. As you will see the SW1 is the Start butto for his machine, the Power can...

Hi sir: Cause: This message occurs only in connection with a PDR board installed. The message is output during a cut release, if the computer detects a difference between the nominal and actual values of the clamping pressure. The nominal value results from the machine parameter setting. The...

Hi Rodrigo Maybe i can supply, let me know 1) ID plate 2) Serial number 3) Part number 4) Delivery country for freight. Thank you in advance, sincerely. Blessing [email protected] Mobile+WhatsApp;+505 8861 1441

ok sir Please do this , in order to clear the error. 1) Perform a visual inspection : look for loose and broken wires, improperly seated connectors, loose or broken wires misset switch, missing jumpers. and so on. Chech for obviously damaged component(components burned or discolore due to...

ok sir Blessing [email protected] Mobile+WhatsApp;+505 8861 1441

Hi sir; Please following this Troubleshooting; Click the "Error messages" button. The following help information is displayed: 0 Error code 0 Description of error 0 Error remedy 2. Follow the instructions to eliminate the error. 3. Click the "Correct error" button. This action returns the...

Hi sir You must go to the Diagnostic screen, for to see what going on? Blessing [email protected] Mobile+WhatsApp;+505 8861 1441

Send me email Blessing [email protected] Mobile WhatsApp:+5058861 1441

Please follow the steps indicated before Yesterday at 6:53 AM Add bookmark #2 Hi sir; Once a cut has been terminated and the knife returned to the upper dead centre a timer is started (10 seconds) in the course of which the clamp has to recognize switch B29. If the return of the clamp is...

Hi sir; Once a cut has been terminated and the knife returned to the upper dead centre a timer is started (10 seconds) in the course of which the clamp has to recognize switch B29. If the return of the clamp is not registered during this waiting time the above error message is issued. Check...

Hi sir Normally when this happen, the inching button is dirty, try to clean it 2) see if they are loose wires, or corroded, or connector dirty, clean it very well. and replace it, if necessary. 2) clean all Edge connector of electronic board, for corroded, and loose wires,this is most main...

ok sir. Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Thank you blessing [email protected] WhatsApp:+505 8861 1441

Hi sir send me his email, for to send you operator manual in English Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir: Normally, this machine has electronic board BLT4, with many electronics components. 1) PTC resistor for temperature, can be defective for possible increase temperature of main motor. 1a) Review all power supplies of the machine IF they are in TOLERANCE, like +15 -15 2) interference...

Hi sir send me his email Blessing [email protected] Mobile+WhatsApp:+505 8861 1441

Hi sir; Will be a great Idea, if you use better Soap, if very Powerful tool, for detect leaking in any system Hydraulic, or Pneumatic. For other side is more cheape, and effective, in that way you can detect, if there are others devices, are leakings. Let me know, in order to help you...

Thank you Carlos; Will see what will happen. Send me his email, for to send you the quotation, in case that I did receive the same Thank you in advance, sincerely. Blessing [email protected] Mobile+WhatsApp:+505 8861 1441 Managua, Nicaragua. Central America

Hi sir; Go to the 1) service menu; Here is Hot Key Function Description PREV + NEXT + MENU Service Menu Provides access 2) Use too the Diagnostic Menu; Press MENU to access the menu sub-system, then press SELECT until DIAGNOSTICS is displayed. Then press NEXT to enter the Diagnostics menu...