Search results

May be time for a good cleaning including circulation pumps, plastic pipes, drains and all. Put everything together, run without filter, fill with water and make sure it circulates properly. If there's a spraybar in the dev section make sure you clean its holes with a toothpick at every...

My two cents worth, this is an oxymoron. I don't think there's a way to control the backlight and/or ambient illumination to justify an attempt to create a color profile. But I may be wrong.

Illegal file name containing high ascii ? Error : Unable to convert NT/MAC filename! Possible causes: Error : JobFiles:79100-79199:79152-Music Doing Good:Production EPS-PDF:79152.pdf

You must also inform the machine you've changed the finisher and filters, go to control panel > Main menu > Change menu > change Dev (i.e. finisher) , change dev (finisher) filter, return to main menu. Do you have the operator manual ?

What plates do you use ? Turn off machine and drain the finisher into a suitable plastic container, look for the big red painted drain valve very close to the black small replen filter. Clean all rubber rollers and guides, clean the finisher tank with water. Clean the brushes properly. Close...

You won't see much with 10%. Do a 50% grey test (or even 80) full area as advised because it will (mosy likely) rip as 45 degrees making artifacts more visible. Did you check the processor ? Just asking why do you measure density instead of percentage ? I have processed the picture you sent...

One more thing I've seen old film processors with worn out rollers and bushings unable to pull film smoothly, you may need to check dev section rollers and gears moving easily driven by hand. Again, the uniformity test I described will tell the drive system condition, look for banding and...

New chemistry does not rule out the processor. Make sure you use the correct developer and parameters are checked - temperature stability, machine speed and recirculation pump condition being the most important. Expose a 50 percent raster rectangle full size to test uniformity ; cut, process...

Lots of things to look for. All processes started ok before running User Interface or Meta / Comms running ok between computer and ctp, do you receive status messages from ctp in U.I. / Any errors in event viewer / Task manager looking clean, with normal legit processes a.s.o.

Hi again try temperature controllers at mouser, farnell, industrial automation shops. I found a digital Omron controller called E5CB at mouser, suitable for almost any type of input (you have K probes), powered by 110-230VAC and one output on standard relay or SSR. Needs a square hole, 48x48 mm...

You can find the operating instructions manual on the internet. Snip ... to determine the Set Temperature, with the heater switch activated and the current temperature displayed, press and hold down either the up or down arrow for 3-4 seconds. The display will change and flash the Set...

Open the License manager and check what software version your dongle unlocks.

I've sent you a private message.

Hi suzanncrist, gripper margins are specific for each offset machine. What presses do you have there ?

If your press console runs Windows and can browse the hard disk and attached drives, are you able to read anything from that card ? If you see any files in file manager or explorer with names ending with .ppf but they don't come up in your working interface it is possible the PPF files are bad...

It's not about what others prefer. The plate processor you need must be suitable for the ctp you have already (or intend to buy) in terms of plate type being used, plate maximum width, speed, plate entry height, serial communication if needed. Once technical matters sorted you will choose the...

I don't know about viper 3 but ADB dongles for old harlequins cannot be ported to G4 and above macs as security drivers ask for direct connection to the ADB bus. USB to ADB adapters don't work. Beige G3 platforms were the last compatible in the line. Just a thought.

AFAIK, infrared film has been discontinued by 'all three' manufacturers long time ago.

You need a specific Ripmate for DPX. Buy a new one. Not so expensive, really.

Four squared shape metal brackets securing the drum to the machine frame base.