Search results

1. CTP: on production since june 2009 Kodak CTP Trendsetter Quantum 800 format B1+ Kodak T800 processor Kodak plate Staker Serwer Dell: RIP Kodak PRINERGY 5.3 Preps Plus 5.5 imposition Back UPS 800 Monitor Dell 2450 Xrite CTplate2 - 2. CTF Agfa Avantra 25 2003 format 449x635 mm RIP...

I have just made the Photo. It seems that it is not possible to take ou the sensor for checking without removing the platen above.

thank you for the relevant pages of service manual. But there are two problems. First I still can not find out how to get into sensor and there is different mounting of sensor as described on Fig 5.30.

Again the problem appeared. The diagnostic program does not find any error in tests. But any action causing film forwarding stops with 62 error. Display Sensor menu shows the takeup Casette jam and media presence detector properly. We do not know what to do. Additionally we do not know how to...

Thank you for the answer, we have checked the sensors and corrected bad connection in one. It works now. Vlad, could you please send by e-mail ([email protected]) the full list of error codes? We have lost the manual when moving the firm to the new location.

We have problem with winding the film to output Casette. When we press the cutting button we get the error code 62. Cutter work perfektly, there is no jam with the film. Any suggestions?

We get the error message "timeout moving roller cylinder". What can cause the problem?

We cannot afford to ask Kodak for help. They charge 1200 Euro for visit of serviceman. We would not ask in Printplanet if we could hire Kodak.

We have to move Trendsetter 800 to the new location. What precaution we need do take into account?

We have kodak trendsetter 800 quantum. We look for service independent from kodak. Any suggestions?

We have problem with the the Gear Speed Reducer for the motor driving main rollers. We have found that gear box is produced by the chinese Linix company, model 90JB. How to get that part. Linix does not ansewer e-mails.

Hi, probably the blower in Universal Debris Removal Cabinet has burnt out. Do anybody know how to get it out in order to repair it?

Yes. We still do not know how in easy way change the motor spring, but as I have written before higher value of motor current have cured the problem with proper film winding. We shall try your suggestion about rubber wearing when problem will shows again. Thanks for the problem watching.

Thank you for the extensive reply. We did the test with the opened lid. We have had errors concerning the proper grabbing of the film by core clams. But after reducing the speed of core rotation and adjusting the tension we have eliminated that problem. But still we had the problem with propoer...

I have set up the msn account: [email protected]

Sensors were cleaned, cassetes checked (read our previous posts). I do not know what do you mean by Nip. We do not use msn or yahoo massenger, but we can set up msn on wish. We use Skype. our nick is vogar_wojciech We can also communicate in German if easier. No offence. Wojciech

It is pity, that we cannot perform any test procedure by ourselves. We do not get any non specific error code. Only the standard one - number 6 film jam.

If I only knew how to get into the service procedure from the panel. I know how to get in SelectSet5000 but unfortunately not for Avantra25. Any info would be appreciated.

Avantra film stacking Avantra film stacking Thank you for the suggestions. However I do not understand what means adjusting clutch spring. The clutch lips work gravitational. The only two springs which I see in cassette are: one to open cassette slot and another one to change the friction on...

Stacking film Stacking film Thank you for the clues. One have to press the wheel pretty firmly to stop it. We observed loading of the film into casette with opened lid. Not every time the clutch grabs the film properly (film pass by) or if grabs properly does not wind film tightly. It suggests...