Search results

Are you sure it's a serial connection? If it's connected with an actual serial connection, it's likely going to take the same model UPS for the communications to work. I know many industrial UPS boxes have a 9 or 25 pin connector that looks like a serial port, but many of them are just discrete...

Recently I was contacted by a former employer about the possibility of returning to work for them, I was forced to politely decline at this time based on what I see in the industry in my area. There are still shops closing, being sold, etc. Beyond that I am not too sure about the state of the...

I saw something similar once, the job was printed, AQ coated, folded and boxed, Upon delivery to the customer the boxes and contents were hot, and the entire job was now bricked (coating). Samples were sent to some experts, it was discovered that an exothermic chemical reaction caused the problem.

Sorry your having trouble, I did also. I was forced to leave the printing industry after a 22 year Field Service career. I should have done it years ago instead of hanging on until I was forced to move on.

We better call on someone closer than that for help. Seriously, I felt the industry decline to the point I was forced to change industries, so far it was the best decision I ever made.

Where there are four printers there is always a fifth.:p

Bottcher rollers are not cheap, or inferior. I suspect if Heidleberg refused to use them it was for another reason other than their quality or performance record. If press speed is damaging rubber rollers I would say there is a problem with the inker cooling system.

I know USPS is not replacing many employees as they retire or move on, this places an extra burden on current employees, after they finish their route they continue working on a route that is not their own. This may be an explanation for the later delivery times. On the issue of not getting...

I assume you need a thyristor for some kind of motor drive unit. you'll probably need a part number off of the semiconductor itself to get a replacement. I know nothing about the drive I assume you are working on, but I have repaired a few older drives that had thyristor (SCR) outputs. I would...

The Komori operation manual gives these roller settings in nip width, not pressure. I am not aware of any accurate way to convert a pressure measurement into nip width, as even slight deviation from the given roller hardness would affect the final nip width. If you want to use a digital gauge...

Yes Erik, You are correct about the ink ductor, I found a newer explanation of the ink feed system (see note 4 at the bottom). I don't think there is a way to increase the total range of ink key movement, the key motors have a finite amount of mechanical movement. In fact on older machines...

Kind of depends what kind of print quality you wish to maintain. For optimum print quality, the water rollers should be checked regularly, and likely replaced every 6-9 months, maybe a year if you're lucky. Ink rollers not as often but are just as important IMHO. Get yourself a good durometer...

Graphical representation of the SET and RATIO functions The synchronization point is the press speed that changes from SET to RATIO setting, set by console memory setting M2-1 (default setting is 38 i.e. 38% of max speed) Although if I remember correctly, this setting may have a slightly...

Yes, all it takes is one tiny pinhole and the fountain solution begins getting under the chrome and attacks the roller underneath. it will cause a bubble it the chrome that will eventually flake off. In the past I found a common issue was on a 40" Komori, when taking out and installing water...

As long as the perfecting mechanism is sound at that speed, it should be good. The question is, how many jobs will you actually be able to perfect at 18000 iph? I can guarantee you at some point there will be someone try to run a low grade garbage recycled substrate and expect it to perform...

There was a change made between the Lithrone series and the LS series, as far as I know all of the 40" LS presses have 35mm keys qty 30, A Lithrone 40 has thinner keys, sorry I don't have the spec handy, but a Lithrone press (previous to the LS) had 34 keys.

The cloth already has soaked up chemicals / ink in it, so it not going to be as effective the second time around. Why not just idle the press at run speed for a minute or two to dry the blankets off, that's what some of the newer equipment does, just to air dry the blankets.

I can also vouch for Hardronics , quality work, their chrome rollers last.

Be sure to find out the cost of the ink roller bearings, and specifically ask if they are patented by Man Roland. That's about all I have to say about that.

Some sort of tool post grinder with various grit stone wheels for grinding and polishing. When I was a field service rep, the company I worked for had a roller manufacturing/recovering department at one time, the grinding attachment went back and forth as the roller turned and ground / polished...