Recent content by elmartin4

I have the message "90 10" on panel feeder in my Man Roland 105. I do not know what it means. Where I can get a display messages book?. These are not a display messages section in the operator's manual.

Vlad ... I have a CTP Palladio and am using silver halide plates. Due to the growing scarcity of such plates, I am investigating whether it is possible to change the laser unit to process Thermal plates. Do you think this is possible?. Greetings.

Really is something I discovered recently...

I solved the problem. For some unknown reason the CTP ID does not match the ID of RIP TUNER, one was 8 and the other 5. Vlad: I have a driver palladium Apogee PDF Rip support, which should be installed only with version 2 of Apogee PDF Rip, that is, before installing any update should install...

I have a Palladio CTP with Apogee PDF Rip. Apogee Rip Server display this message: RIP performed an anormal shut down. Unable to conect to engine. What can be causing this problem? I appreciate any help.

Thanks for your answer, VladCanada. Really helped me.

Palladio CTP. I have a problem, get a spot along the plate, as if in that area the laser does not come with enough power. I checked the rule development process for processing failures Agfa LP86, all is well. What do you think is the cause of this failure?

Agfa LP68 ULTRA processor displays: U2 100 error. I consulted the manual operation and says: LMD board (U3) off-line. I do not know what the LMD board or where is placed. I do not know what it means to U2 or U3. any help will be appreciated.

Agfa LP68 Ultra Agfa LP68 Ultra I have a problem with a processor LP AGFA Ultra 68, U2-100 errors. The operating manual says: LMD board (U3) off-line. I do not know what the LMD board or what it means to U2 or U3. Any help I will be grateful proportions. Greetings.

hi VladCanada! I have a problem with a processor LP AGFA Ultra 68, U2-100 errors. The operating manual says: LMD board (U3) off-line. I do not know what the LMD board or what it means to U2 or U3. Any help I will be grateful proportions. Greetings.

When you turn on Panther PRO, the diagnostic message is displayed and so all the time. Online's message never appears. The Panthers never fails to display this message even when diagnostic ONLINE key is pressed. When installing the Panther disc in a PC, is not recognized. Is there any way to...

A lot of Thanks Tekcontrol. I found the Panther Downloader where you told me. However, I can not put the Panthers in download mode. When starting the Panther display STEP 1 DIAGNOSTIC in the control panel and the Panther never goes On line. You know why this happens? ... I tried SCSI...

Panther Pro 46 HS Panther Pro 46 HS Thank Tekcontrol. I found the Panther Downloader where you told me. However, I can not put the Panthers in download mode. When starting the Panther display STEP 1 DIAGNOSTIC in the control panel and the Panther never goes On line. You know why this happens...

SCSI hard drive Panther PRO 46/HS SCSI hard drive Panther PRO 46/HS Hi, Tekcontrol... The last time we spoke I had problems with Panther 46/HS PRO. Well, I resolved the above problems. But now, one of the two SCSI hard disk of the Panther PRO 46/HS is damaged. It is the boot disk. if you can...

It damaged the SCSI hard drive 46/HS PRO Panther. It is the boot disk. if someone can provide me the software to load it into a new SCSI hard drive, or if someone can sell me a new disk with Panther operating system loaded, please contact me in this way or send an email to [email protected].