Recent content by gazfocus

  1. G

    Versant 80 - banding?

    Have just tried that as well and no improvement :(
  2. G

    Versant 80 - banding?

    I have printed 100% cyan, magenta, yellow and black sheets today and this issue is only appearing on magenta. I’ve also swapped the magenta drum out for a brand new one (again) and still getting the issue. Also cleaned the ROS windows and still no improvement.
  3. G

    Versant 80 - banding?

    It runs from leading edge to trail edge.
  4. G

    Versant 80 - banding?

    Thanks for the suggestions. I would have to look up how to check all of that haha but will have a look tomorrow and post back :)
  5. G

    Versant 80 - banding?

    I’m a Konica fan but recently bought a Versant 80 as a cheap(ish) second machine and have no idea how to troubleshoot it haha. Printing some greeting cards and getting this banding on pink and purple. On a Konica I’d say it’s the corona wires but don’t know if it’s just the drum on the Xerox...
  6. G

    Versant 80...All lights flashing

    I had hoped that one of the cables was loose and that it'd be a simple fix but turned out to be a dead power supply.
  7. G

    Versant 80...All lights flashing

    We had the tech out yesterday and he was of the same opinion as your tech that one of the two low voltage power supplies had failed. He's took the first one away with him to test on his machine (apparently the second one is more difficult to get to so he didn't want to take it out if it wasn't...
  8. G

    Versant 80...All lights flashing

    I left the machine overnight and did as you suggested this morning but still no joy. I've had a reply from the company I purchased the printer from (who the maintenance contract is with) and they are going to send an engineer out. Not a good start though haha.
  9. G

    Versant 80...All lights flashing

    Thanks, I shall give this a go
  10. G

    Versant 80...All lights flashing

    I’ve sent them the video but was hoping it’d be something simple that I could fix to get me up and running.
  11. G

    Versant 80...All lights flashing

    It is on a service contract, yes.
  12. G

    Versant 80...All lights flashing

    Anyone with a Versant 80 experienced all the lights flashing on and off? We only had this installed on Thursday, left it over the weekend then came in today to this. Have tried powering it off at the wall and leaving it for a few minutes but just reverts to the same state when I power it back...
  13. G

    Skew on Morgana Docufold Pro

    Hi Halmac, Our plates don't have skew adjustment on them I don't think as it's all done digitally. There's a roller tilt lever which, according to the manual, is meant to fix skew but the paper is still skewed regardless of where that lever is positioned. I definitely think the company I bought...
  14. G

    Skew on Morgana Docufold Pro

    Just thought it worth mentioning, I've just ran a few sheets through my Duplo DC-445 creaser and they've creased 100% square. I've also just measured the backstop of the guillotine all the way across and that is straight (I did have my doubts haha). So, it's something with the Morgana. I've...
  15. G

    Skew on Morgana Docufold Pro

    Hey. Thanks for the input. I've checked the paper and it's definitely cut square. I've even tried with uncut paper straight out of the packet and it's still skewed. What I think you're mistaking for cracking is something I've only just spotted but it's on the opening edge of the leaflet, not...

What About Profitability?

Canon
What about Profitability?
Offset yields new advantages

Read All About It

 
Top