Recent content by Yoana

  1. Yoana

    firmware of Agfa Avalon Screen 4300

    there is no agfa service in venezuela
  2. Yoana

    firmware of Agfa Avalon Screen 4300

    I am looking for the firmware of Agfa Avalon Screen 4300 year 2011
  3. Yoana

    My CTP Avalon n4 stays in "memory checking" forever

    Hello! It has been almost a year since I posted on this page, but the condition of my equipment remains the same. wow, we have tried many things through the softwares and versions. The last test that was done was to remove the panel and connect it to another machine, to another ctp of the same...
  4. Yoana

    My CTP Avalon n4 stays in "memory checking" forever

    Hello, nice to meet Ernierad, in fact I have changed the PIO board, the CPU borad or the so-called RCP3E board for new ones, I have already installed the firmware, I connected the PC and I was able to save the configuration data of the previous RCP3E card for the new one. And nothing, it...
  5. Yoana

    My CTP Avalon n4 stays in "memory checking" forever

    Hello, Leo, Yes, I have WhatsApp- The news is that I have managed to enter the system menu, through the touch panel, but when I want to initialize, or run, the machine does not work anyway. I think you have to load the software, or verify parameters, or re-establish the system. Do you have any...
  6. Yoana

    My CTP Avalon n4 stays in "memory checking" forever

    I am in Caracas - Venezuela. There is no Agfa technical support in my country. Regarding the Avalon, I already replaced the PIO card and the RCP3E memory card, but the machine continues "Checking mememory" and from there it does not progress.
  7. Yoana

    My CTP Avalon n4 stays in "memory checking" forever

    Hello friends, we have a CTP Avalon N4 that presented an electrical short circuit and we have already replaced the power card but the fault persists and now, the technical support indicates that I must change the memory board, who has had experience on this? the device turns on but does...
  8. Yoana

    Bindery Help - Orlando, FL area

    Hello, my pleasure, my name is Yoana Gonzalez, I saw your post and do not hesitate to write to see if you can help me with the following technical problem with a trilateral guillotine brand Toledo and model HD 1680. The problem is that as soon as I turn it on I get error 101, I lost connection...
  9. Yoana

    Agfa Avalon LF Thermal .. Laser Problem

    Hello friends, we have a CTP Avalon N4 that presented an electrical short circuit and we have already replaced the power card but the fault persists and now, the technical support indicates that I must change the memory board, who has had experience on this? the device turns on but does...
  10. Yoana

    ECRM Mako 56 have a problem

    In our CTP Mako the lithographic plates were going out crooked. the perpendicularity test did not give a convincing result. We have noticed that the arm where the pin bar is placed is slightly crooked, definitely this should influence at the fault that I have. Perhaps it has been damaged by...
  11. Yoana

    ECRM Mako 46 have a problem

    In our CTP Mako the lithographic plates were going out crooked. the perpendicularity test did not give a convincing result. We have noticed that the arm where the pin bar is placed is slightly crooked, definitely this should influence at the fault that I have. Perhaps it has been damaged by...
  12. Yoana

    ECRM Mako 56 have a problem

    Thanks for your help, I'll try that
  13. Yoana

    ECRM Mako 56 have a problem

    I write this to technical support hoping they can help me or clarify me about a problem I have with my CTP MAKO ECRM model 111111X38 . The problem I have is that I present the plate at the pin bar and everything looks ok but the image is crooked. I did a test with a grid and it is observed that...

What About Profitability?

Canon
What about Profitability?
Offset yields new advantages

Read All About It

 
Top