Search results

Few questions - Is this happening with all coatings (gloss, satin, and matte) or just one in compared to another? Have you checked the stripe thickness and verified that you're not overpacked? If you needed a quick fix, clean the blanket the best you can with either coating cleaner or...

Quoted - instead of a dotgain, i get dotloss of -4 to -6 on almost all units running cmyk. For starters, measure the dot on the plate to verify where your starting point is. Is really doesn’t matter whether you start linear or not as your cutback curves are going to be calculated on L*a*b*...

Based on your pictures, the inks are curing on the fount ball. As they are curing on the ball roller, then are collecting debris (cured ink) and creating uneven pressure between the liner, ink keys, and last fount ball. Get the overhead sleeves and get a thicker ink fount liner (.12 or .14mil)...

I personally service A LOT of UV, H-UV, and LED offset shops (everything from high end commercial to packaging) on all types of presses from Heidelbergs, KBA's, Komori, RMGT's. These shops are running process and in and out of PMS colors all day and I don't see that. Where I have seen this...

Quick Questions - Are you running standard Mercury Vapor or LED/HUV inks? Do you have light filter covers over your lights above press? Is the ink demonstrating a "hide" or clumps after some time in the ink fount? Could be the ink's monomer / oligomers are diving into the rubber. That can...

The true and accurate way to measure TVI (Dot Gain) is by knowing what the dot on the plate is first. From there, you can measure your screen tints on the color bar to really know where you're at. Hope this helps!

Respectfully, I would get in the general practice of changing water out weekly, unless you have a Floclear system and are constantly replenishing. Founts (regardless of manufacturer) will have a working lifespan. Some contain organic gums while others have synthetic gums. That said, newer...

CKL - Good points. If he's running a roller coater, than BCM is irrelevant. He can certainly check his coating stripe and measure viscosity using a Zahn #3. Aqazi - Is this happening with Gloss, Satin, or Matte? Or all coatings?

Mud Cracking. The coating is drying faster than the ink underneath. As the coating is applied to the film of ink(s) underneath, it's crawling giving the 'Alligator Skin' look. Talk to your coating suppliers about a slightly slower drying coating.

Pauly, Thanks for chiming in. I've created media profiles, then applied the destination ICC. I've tried applying device link profiles with the intentions of driving all the Deltas for RGB and CMYK to the lowest possible. If submitting G7 gray scale, beautiful. G7 targeted - not happening...

Stephen, The results were the same. Both Red Trap came in at Delta E of 12. Regardless of what actions were taken, no positive improvement was made. This is why I believe that it is what it is and it's just the limitations of the machine. Gray balance - Delta E under 2. Yellow alone was...

No offense taken at all. I'm reaching out for assistance if it can be done. As mentioned, I can achieve a G7 grayscale once calibrated - not targeted. I imported device link profiles, almost the same results as a paper linearization and applying the Gracol 2013 icc. This leads me to believe...

You can't select specific targeted ink densities on this machine with the way Onyx works. You can only select total ink limits with a pass count. Having come from an offset background, this threw me off too.. Tried 300% 12 pass, 340% 16 pass. Same results.

I was wondering if anyone has successfully done a G7 Targeted (Not just a G7 Gray Scale) calibration on an HP360 latex? If so, can you please elaborate what rip/work-flow, ink limits, etc. were used in the process? I tried curving it, tried device link profiles, tried an optimization - no luck...

Ink Density - Hand Held Spectrophotometer (Try X-Rite or Techkon) Fountain Solution Conductivity - pH and Conductivity Meter (Try Myron L or Hannah) Is this for pressroom Q.C. purposes or for ink manufacturing? I'm familiar with printers adjusting pH of inks within Flexo applications but not...

I think the point is that this is a Toyo senior ink tech trying to reach out in cyber space for tech help. Why wouldn't you ask one of your fellow co-workers, field tech service reps., or distributors for assistance with trouble shooting on YOUR OWN PRODUCT. Surely there is someone out there...

Dirty Fount Blade Ink Skinning/Drying on the Ink Fount Roller Severe - Poor Grind of Inks

Bret, We on this forum are all here to positively communicate, network, and share positive contributions via debate. I applaud your chiming in but you don't think that the tolerances are a bit stretched for compliance now? Printing with B*-2 and B*-6 and still achieving tolerance is insane...

In my opinion, GRACol 2013 was released premature. #1 - The white point has changed from a b* of -2 to -4 with a plus or minus of 2. This means that in order to be "Certified" on any G7 submission, you can be anywhere from a B* of -2 to a -6. That couldn't be farther apart on opposite ends of...

If it is starting as picture framing on the plate and starts moving inwards, it is certainly "Counter Etching." I've seen this with all major plate brands over the years. This is not exclusive to one particular plate, brand press, or offset roller company. Counter Etching is a direct relation...