Search results

  1. G

    MAN Roland 202 TOB

    Have a look for dirty sensors in your delivery? Perhaps the pile lift/lower sensors are stuck.. Other than that I dunno :/
  2. G

    Dampening Issue on Komori Press

    We are not a big company but turn over a lot of work and use a heap of consumables: the 40" and 26" printed over 300,000 impressions over the weekend!! It seems to have been that the rep left, and everything was then ordered through a central location.... Ordering fountain solution and other...
  3. G

    Dampening Issue on Komori Press

    Do you run IPA at all? We had some issues with Bottcher 300(can't remember the last digit!!) that are similar to yours, and a switch to 3021 cleared everything up nicely.. Previously we were running an ABC/Allied supplied fount called "Greenfount" that worked quite well, but a complete lack of...
  4. G

    Four color printing on two color press using powder

    Ha used to do the same thing on a Solna 125 or a GTO46... Kept you on top of your game!! We had a Chief too.... But it would not register at all: we did get it for free so maybe it had seen a smash or two...
  5. G

    Four color printing on two color press using powder

    Unless it's an epically long run, run it back through and de-dust it next time!! Oh.... And turn off the spray powder when you do this lol... I've De-dusted and left it on before... Defeats the purpose hehe :)
  6. G

    Water pooling at the bottom of solids

    Maybe worth testing your levels then... Perhaps your doser needs priming and isn't sucking up fountain solution, or it's a possibility you've botched the percentages when hand dosing? No other changes to chemistry? Did you run a cleaning solution? It's possibly contaminated so perhaps a dump...
  7. G

    Water pooling at the bottom of solids

    It might just be a case of fresh, new solution and water may be providing you with better dampening all over? Have you been able to drop your water feed speeds down in general?? Perhaps your pre-damp settings can be dropped to "low" as well (if applicable on the press you're running)... We've...
  8. G

    Blanket Cylinder packing: hard vs soft?

    Hit the nail on the head Luke. Working with pre press at my factory is an exercise in frustration.... Apparently imposition and plate making is the limit of our pre press, anything else results in "PDF, can't change it, your problem". Maybe I shouldn't have (less than diplomatically!) reminded...
  9. G

    Preventive Maintenance

    As stated, the operation manual is your most important tool with regards to maintenance. You'll be able to pinpoint every grease point on the press and it will provide you with the correct procedure and time frame in which particular grease points require input. Honestly, you'd be suprised how...
  10. G

    Blanket Cylinder packing: hard vs soft?

    Forgot to report back on the results of swapping to hard packing!! Have ran a few jobs now with the harder packing under the blankets, and must say I'm reasonably happy with the results. I'm getting a sharper dot and visibly less dot gain (visual check only) which means matching a proof has...
  11. G

    Water in ink duct

    I agree Luke..... But it's unfortunately never that simple :( We run bulk run mail out 95% of the time with heavy coverage. The Hostmann bloody Steinberg ink we use tends to get EVERYWHERE. On a deck that's less than a year old, that I've pulled apart several times to clean, it still required...
  12. G

    Blanket Cylinder packing: hard vs soft?

    Yep that's what I've got now.... The last lot of under blankets we got from Bottcher were the red/orange type with a very slick surface, as opposed to the flat grey ones we previously ran. Four times they slipped out of the clamps, even after I put in new screws and used a file to rough up the...
  13. G

    Water in ink duct

    Do you run a roller conditioner program? We don't..... But last week I had to put a varnish on the 4th (yellow) unit, and in the loooooong process of getting it clean enough to varnish I ran through a complete conditioning program with calcium rinses and rubber conditioners etc..... Took...
  14. G

    Blanket Cylinder packing: hard vs soft?

    Currently we run a single Bottcher 1.0mm under blanket, I've got some of the under packing board to trial on it tonight if I'm able...
  15. G

    Blanket Cylinder packing: hard vs soft?

    So what are your preferences and why? We have been running soft packing for quite some time now, with the (perceived) benefit of giving the blanket a little more resistance to minor smashes. In this regard they seem beneficial: they'll take a hit and survive (until you put on a high-end job!)...
  16. G

    water chemistry - what are we all using?

    Komori 40" or 26" using ABC/Allied supplied Greenfount, tap water and 5% IPA.
  17. G

    Top Quality Printing - how is done?

    You can't make a silk purse out of a sow's ear.... Or so the saying goes. If all the elements involved in printing come together as one, a combination of good consumables, good stock, good machinery, good operators, good pre-press and good finishing crew..... Well it still won't matter if...
  18. G

    is it possible?

    I would think that with a clever enough engineer and sparky it would be doable. Obviously you're going to have to look into the voltage requirement of the lamps and upgrade wiring etc to suit, and as Cornishpastythighs suggests be very aware of cooling requirements as a fire could easily result...
  19. G

    Hostmann-Steiberg Inks

    The ink I trialled was had "Toyo Hyplus" on the box, though the canister was unlabeled so I can't be 100% sure that this was the actual ink. We also have some "Best One" to try: I'll throw some in on Monday... Interesting that you mention dot-gain too Luke: dot-gain has been markedly increased...
  20. G

    Hostmann-Steiberg Inks

    Mazengh: I will talk with my boss about it and see what we can do: aside from the instant improvement in print quality and consistency, I noted a large increase in mileage too: it appeared (in a highly un-scientific, seat of the pants test if I must admit!!) to use much less ink over the print...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top