Search results

Richard The part you are looking for is an IO board for hamada B452 part number E42-91-01-3 Marc

me.awash you May have a problem with the fiber head not sliding smoothly on one side of the Vgroove. When last was your Magnus Serviced? the Tech normally cleans the Vgroove and replaces the Oiler brackets as part of a PM service. There is a specific silicone oil that is used for lubricating...

Hi Wojo The Fanapart glue was always applied to the edge of a stack (more than 50 sets or so) of collated sets of sheets with a large paintbrush. The paddywagon just held them together like a large pad of papers. When the glue dries it seems that the capillary action allowed it to go into the...

Hi Michel Can you supply more info? 1) What Rip are you using 2) Are you using a tiff catcher to drive your CTP 3) What CTP device are you using Marc

Dear Admins I have recently posted two answers which suggest the OP consider products that I sell in my Market. I am concerned that this may be considered spammy behavior. I've tried to send this post as a PM to prwhite as a PM but got an error that this user has exceeded their private...

Hi Sniper2075 Ok, I suggest that you consider a purpose built system for label printing, roll to roll which will eliminate feeding issues. If you were a client in my market I would suggest a Uninet iColor 700. The maximum printable area for a label on this machine is 8.24" x 52”. You can see...

Hi Budgetprintsgreen Unfortunately I'm not a pressteck Tech, so don't have the info. I did read that the Dimension lasers are somewhat unstable at lower powers so this may not be a solution for you since balancing the multiple lasers on these devices has been said to be very difficult, more so...

Hey Repro While its possible, it seems to me that me.awash is experiencing an exposure issue on one side of the plate based on the evenness and repeat-ability of the lines. I would not expect such consistency for a processor based problem. of course you could hide the problem by delivering more...

Hi Raminmind I'm looking at developing a solution similar to what you are describing for one of my customers. In our solution, we are looking at chiliPublish for the design portion. If you are a developer, I suggest that you have a look. Fair Disclosure: 1) I am a vendor. 2) This is not an...

Hi Sniper, Just Checking, is that a typo or are you actually printing 21.5 inch long labels? Marc

Curious to learn which one you decided and what your advice to others would be

Hi Brunswick You may be able to reduce the laser power value in your CTP down to where it could successfully image Kodak Sonora plates. You will also have to change your imaging setup so that you write the image area and not the background as you did in the previous Presstek plates. These...

Have you looked at Appvion as a potential supplier? They have a product that is designed for xerographic (as in Toner based) printing in 6 parts pre-collated for loading into a laser printer.

Hmm, wondering who Toys 'R Us could be.. perhaps a company with the first and fourth letters of the alphabet in their name?

Unless you are into programming and have a lot of time to learn the intricacies of writing postscript programs, I would suggest that you stick to using tools like Illustrator and Indesign that give you a graphic interface to get what you want done. Raw postscript is extremely powerful but also...

Hi me.awash, What CTP imager are you using? Does it support calibrating the laser diodes individually? What is the width of the space between the lines? Do you see this problem on smaller plates? These types of vertical lines look like the width of the swath is not perfectly aligned. It...

So if you are going to do this digitally, you wont need/can't easily get the tractor feed holes. These are not normally required unless your customer is filling the forms info on an old DotMatrix printer. You can buy Carbonless paper (e.g. NCR) and collate the sheets then print them in your...

Baritone, what kind of support are you looking for? do you have a specific issue you are dealing with?

Duncan, that will mean you have to teach the Robots how to smoke a pack a day ;)

Lotem Diodes Lotem Diodes Diodes for the lotem series of machines are normally only available from Kodak. You will also need to have a fiber optic splicer and a Tech that knows how to do the job. Hope this is not a problem, but your best bet would be to contact a Kodak Service rep. Marc