Search results

Canon IPF765

Being a Presstek dealer we have not seen any change in daily business

Check your air filters on your pump non-op side below feed table. If you run spray powder they get clogged. If they are clean check hoses off or cracks in them. Good Luck

The knocking is the paper snapping when it is transfer to the cylinder grippers. There is nothing to worry about it just because the paper is long. It might go away if you turn the speed up.

Our folder the hand wheel is geared in with the rollers and it will turn over Even if the belt is off. Does the motor kick on when you hit the start button?

Did you check the drive belt they fall off somtimes.

Keep in mind that if you rotate this knob one full rotation it only moves 1 mm if you are used to an Abdick where it moves alot.

Count the sheets before you run them through the digital machine the keep track of waste and you will know the end count for sure.

I think the just need to adapt to the changing times people are emailing because it is cheaper and easier. That is never coming back. Raising the prices is only going to drive more people away from it. They stop at most addresses in the U.S. of course its not effiecient to drop one letter off...

Hey all, I run a small 4 color ryobi and have been having issues with cover stock. The Last Month or so The paper I get from the distributer every other sheet has a different curl to it (one up and one down)We use all kinds of sizes and weight and Most of them have it. I have seen it in on...

Pressmanken, If you watch the envelopes when they transfer to the feed rollers the sucker feet drag on the envelope causing abraisions which tranfers to your blanket in turn wrecking your plate. Sometimes you can run the envelopes without using sucker feet. This will help. good luck.

Is it showing up on the first unit more than the second? If so it usually the paper fibers from the envelopes. Check your blankets if there is paper dust on the blanket it is wrecking your plates. The only way to avoid this is wash your blanket and make sure the all the dust is off your...

We alway adjust the front panel with wrap around on the cutter. We cut the front panel longer and the back shorter. (then you have less chance for dog ears when you have a letterfold) we also cut one out by hand and hand fold one before printing. We all know there are those exceptions. Then you...

The problem is the dampening system Kompacts or the one you have just dump way too much water on the press thats why the never tone. You can put all the dryer you want it will still take forever to dry. The key to getting it is cut the water back as far as you can. We have a kompac on a A.B...

Static products do not work on this problem. I have tried them all. This is caused by the friction of the tapes on coated paper. Running curl up first helps, less tapes on top of paper.

reyhub Here is a solution for your issue. take the removeable silver clip that are under the feed tapes. Put a laminated strip of chipboard 1.5 x 11.5 attach to silver clip should run from angle iron in front where the numbers are to on top of the bumpy feed table. Use scotch tape to attach...

Do you have a Kompac on there if so there is a copper and silver nut at each end one is the locking nut i think the small one is the locking. Loosen the small and turn the large one until you have a 4mm stripe even across the whole plate. As for the ink rollers there are two oblong holes on the...

Kramer, I don't know if you fixed your problem here is the answer. there are two square blocks on each side of the feed rollers they have an allen wrench set screw.this is the adjustment for the feed rollers. Good luck.

Alex, I have heard that when you run the first side if you don't wash your blanket the paper dust builds up and causes picking on the second side I have had picking problems on recycled paper more often then regular paper. People blame this on ink and fountain solution all the time, It ussally...

Alex, This is picking what is happening to you. Many things can cause this to happen too much ink or water. If you have the tine to let it sit overnight this is the best cure. another thing you can do if you can't wait. clean back cylinder with a good plate cleaner then use a etch on it. This...