Search results

Hello Looking to buy 2 used but low hours laser diodes for Agfa Avalon N8-50 / PlateRite 8800III machine. LDL and LDU If anyone has to offer, please let me know.

It's NOT ok. Zoom must hold, just like on your camera lens it must be tight seal, not self wondering back and forth. Gear are worn in gearbox not motor it self. That's why there is backlash. You know i doubt we'd face so much trouble for month if we forgot to set media type to nega. But yes...

Found the zoom motor's gears are worm down, motor has enough backlash/free move that's equivalent to 200 pulses. From service zoom position manually, minimum allowed 210 pulses, backlash is same. See video: Ordered new zoom motor from Agfa, not to mention new turbofan. Old one had burned...

Hi everyone Client has old Agfa 8800MKIII that had tons of issue. Previous owner used machine for 12 years straight. After fixing both LD driver boards, power supplies, cleaning all optics and calibrating all motors etc... Machine works and prints well on positive plates (Agfa Elite pro...

We're in the Baltic states. Quiet the distance from PA. But the service manual is only a time saver. The machine is so simple reverse engineering it presents no challenge but it does take time.

Hi Looking for the service manual to the c.p bourg booklet maker and sheet feeder. Machine is experiencing strange communication issues between modules. Maybe someone can help. https://www.upload.ee/image/14172695/IMG_20220526_090936.jpg

Sent

Selling Agfa Avalon VLF micro chassis PCB's, power supplies, motion chassis drives and more. All taken from working unit, tested before decommissioning. List of parts: * CPU PCB (2pcs.) CG+0033740502 * Rotary servo board (2pcs.) CG+0033760501 * Linear Servo board (2pcs.) CG+0033770501 * SDX...

It wasn't about replacing but reverse engineering. Managed to do so successfully and figured out the input control and output feedback.

Hi everyone Got a question about the laser power supply board from an Avalon VLF (60 XXT): the board is controlled by the pelvis board, same that controls the GLV. There is only a 4 pin header connector (J1) between the pelvis board and the laser power supply that sets the laser current and...

Got a problem with an avalon n8-50, error E711d: "When the clamp is out, some tail clamps are detected on the clamp arm, or when the clamp is got, some tail clamps are not detected on the clamp arm" After the plate's been recorded the clamp arm lifts all the clamps off the drum, then the alarm...

Got both, thank you.

Hello everyone Does someone have and could share the user and service manual for elantrix 125 sx OLP?

Perhaps someone has ran in to such an issue before. We had more problems popping out of our VLF 60XXT. Starting with the LR conveyor failing to work in automatic. Now just get the beeper and light indicator with a message to manually remove the plate. Yet works from Unidiag, every command...

Ok Yes i've worked on this imager before. I think i i just had a problem understanding what you wrote the 1st time. Cause cleaning the motor and cleaning the optics are two different things. So i had to ask. On the carriage focus belt i've aligned the encoder wheel with the slot. This slot...

Hi I'll assume you mean 0.38mm. Yes we are using genuine 0.38 mm Agfa energy elite plates from Germany. No i haven't done a mag motor alignment yet. I will try this today. The mag motor alignment, you mean the Xcalibur technical mag Array test? I know with a 100% certainty that the issue...

We have an Avalon VLF 60 TFS that has a blue banding problem. Blue lines (about 7 microns thick) 3.80mm apart are appearing on 16mil plates, vertically along the drum. Something that doesn't happen to any other plate that's 12mil. ​​​​​​I already tried to adjust the belt driven stepper motor...

Always good to start simple. For the chiller, it's set to the same pressure it's always been. Though the machine did have another error many time before. Error number S0CA0 (Hardware: Problem with GLV PFM). Though the chiller is perfectly fine. Checked many times. Proper pressure, so good flow...

We have an Avalon VLF 60XXT CTP that has an autofocus problem. On OCT it's : Imaging: Autofocus controller fault Error C0=53030580 C1=00000066 when autofocus starts: write af:: ss_cnt= 1, onplt_cnt=81, offplt_cnt=0, res_pos = 169 Now i know that if ss_cnt is 0 or 1 that means that it's a...

Thank you Maxon. indeed, as guessed not getting the information that easy. Oh well, seems like always, just got to burn the midnight oiil sniffing trace to trace ;)