• Best Wishes to all for a Wonderful, Joyous & Beautiful Holiday Season, and a Joyful New Year!

Search results

  1. P

    Duplo stitch cartridges

    I did but cant find the box of them. give me a bit ill let you know
  2. P

    Duplo stitch cartridges

    Someone told me the heads from MBM work better. Still about $400 each. The duplo heads are only rated for 30,000 cycles too. Many go a lot further than that and for the cost you would want more. If you know how to disassemble the head there are little tricks that may work.
  3. P

    Duplo 645 cutter/slitter/creasor

    646?? or 645 the older unit? software is not the same
  4. P

    Inline Creasing on a Duplo 618 or similar.

    You folks are all correct. Its 2 different types of creasing. The normal crease bar is best the rotary tool unit does crease but uses rollers/wheels and may crack the print. If its just paper to crease you'll probably be ok.
  5. P

    Duplo DBM-120 error message

    Also the big red emergency stop will cause a cover error. Also maybe you had 2 errors and 1 still is causing it to fail.
  6. P

    How to stop/minimise pages falling out of a book

    Im curious about creasing the synthetic stock as a customer of mine tried on the Duplo and it doesnt crease well. Another person told me that type of stock doesnt crease well for any machine.
  7. P

    Microcut JR Screen Troubleshooting

    Maybe Colter Pederson in New Jersey
  8. P

    Challenge Champion Cutter Help

    As others have said lube the backgage rails. Look in the table slot and oil the screw and along the left side smooth area. Go around to the left side and lube the other smooth side rail. then get that backagae to run back n forth over the lubed area. So many people forget to oil up these areas...
  9. P

    Duplo stitch cartridges

    First Duplo 150 uses different cartridges. As for the 120 cartridges there is a issue with them but nobody owns up to it. I think the glue strip is too wide. Inside the head is 2 tiny fingers that flick the staple forward for the next cycle. If they slip on the glue it doesn't advance and you...
  10. P

    Hydraulic paper cutter and the bleeding of lines? Triumph 5551

    Most if not all will self bleed after a few cycles
  11. P

    Jam code J8 - Duplo DBM-120 Bookletmaker

    Not sure what switch it is but either the one at the fold stopper fingers or when the folded booklet exits the machine. Its at the very end before going into the trimmer. Both switches have a lever type arm. Let us know.
  12. P

    Duplo 645 cutter/slitter/creasor

    I tried sending you a attachment with the disk contents on it. It came back permanent error. I dont think so on the dongle
  13. P

    Duplo 645 cutter/slitter/creasor

    David do you have the disk that came with the machine? Drivers are on it.
  14. P

    Duplo DBM 500 - stitcher unit does not return to the home position

    Never had a machine with 2 different heads. 500 always had hohner.. That area is the wire grip unit. When the internal guts of the head get pulled upwards during the cycle return that grip should close in most cases. If not above that area there is a Allen bolt head in the face plate. Crack it...
  15. P

    Duplo DBM 500 - stitcher unit does not return to the home position

    Remove the drive of the stitcher heads and run a few books without staples. Heads could be the reason your not completing a full cycle. If you still have a problem look inside the machine at the stitcher clutch unit. Big round thing. Spray some electronics cleaner on it to flush away any...
  16. P

    Duplo 645 cutter/slitter/creasor

    Are you in the states? Maybe Duplo or a dealer can get a chip for you
  17. P

    Duplo 645 cutter/slitter/creasor

    The 645 software wasnt hard to install. Im wondering if something is not quite right. TRy uninstalling the software including what drivers you might have and try again. TJ explains is like what should happen.
  18. P

    Duplo DC 616

    Just curious if you were able to find the counts. Duplo gives it an average lifespan of about 1 million sheets of 230 g paper since most people run heavier than that I usually go by 750,000 gives you a ballpark of when your cutter blade and/or slitter blades are getting towards the end of the...

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top