Search results

This error means there is no vacuum detected inside the machine within the allotted time. The light on top indicates the command status coming from the device (it will operate even with the cabinet power cable disconnected) Most common cause is the debris blower motor gone bad, especially if...

"BTW anyone familiar with the Windows app hyperterminal. 9600-8-N-1" That is for MPE only - manufactured until 2002-2003. There are ways for MCE/GMCE too.

There is a big difference between what Creo used to be and what Kodak is from a service point of view. People are mostly the same but upper management vision has changed significantly. In the past, Creo provided service and parts to anyone, sometimes for free, and the focus was on quality and...

Wow.... this is a first If the reason is anything but a reverse engineering attempt, it was a bad, bad move... BTW, if one wants some success with reverse engineering he should know that he must be much smarter than the guys who designed this laser. Theoretically it's not a challenge, but...

...from my Magnus 800 line the most??? Did you confirm the machine is causing the scratches? Can you describe them or upload some pictures? If you suspect the machine, clean all rollers carefully - autoloader exit rollers, drum roller, platesetter exit rollers....

People don't understand that these machines are like a piece of complex software. You download the whole package but you can only run the modules you paid for. Same here - you buy the hardware but you have to run it at the original specs. Upgrades are available if you pay for them. Why is it...

You have the part number wrong.... it's 510P50743 not 510P500743. Kodak should have it in stock.

NJService, I see you are providing service for Trendsetters... how come you don't know this? Configuration passwords were used before the introduction of CFL quite a few years ago. Now, the machine and head type, performance and output are set in the license files

The slow boot has nothing to do with the CTP Power - distribution board Is Windows loading slowly or the Lotem application? I understand that after everything is up and running the machine works fine - please confirm. You need the interlock closed and breaker on for the LBox to get the DDB...

This thread is a month old, but if you still have the problem, follow Pach's advice: "Take the back cover off and clean the V groove ( this is where the head moves) On the bottom Left and Right handside of the Dynamic Optics) you will see White pads that need oiling with Silicon oil" The lines...

Spread the tweezers - they tend to get closer in time - just make sure they get together when closed and btw there is an option to use suction cups to remove paper...

Kodak Trendsetter 800 - is a manual load/unload machine. Kodak Trendsetter News F-AL is automatic with one bay without paper removal features. It can load 2 small plates or one 8-up at a time plus the "commercial" option on the News, gives you higher resolution laser head (2400/2540dpi -...

A Trendesetter can output a 1bit tiff file from any workflow as long as you have a tiff downloader license For Trendsetter I. II, III you need the tiff downloader license for Print Console. For Trendsetter IV you need Prinergy Evo with tiff downloader option.

""Under Harware Tree / centering motor motor if i give home position the centering motor works and moved to home position without any error but if i give end position command the motor rotates on the opposite direction and the centering is move slowly no error. "" Please state again if your XY...

This is a firmware error caused by corruption on MCE board. Usually the board is recoverable and needs a firmware upgrade.

Most common cause of this is the TSP in the Brisque or the DDB card but there may be other reasons too.

It is almost impossible to install a custom OS and have it running due to many old and hard to find drivers. Each machine should have its own OS (win95) image and software CD, and the floppy containing the registry where the machine settings are. There may be a backup floppy with the registry...

Prinergy may be using it's own local or global account for mapping shares which is not related to your user account - check first if anyone played with the araxi or creoadmin account and call kodak for help with shares configuration

Make sure both power cables are plugged in.

With Trendsetter III - GMCE systems, the NIC settings are very strict - stable 1gbit/s, jumbo frames of 9000, bindings order is important and TCP ports free of interference. If you use antivirus/firewall combo always disable it on the GMCE adapter. Some intermediate Intel drivers seem to cause...