Search results

Sorry to jump on the thread but can I ask what vinyl you use for stickers on your wide format (if you do?) We are just getting into eco-solvent and bought metamark MD100 vinyl and it feels very thin once it's been printed on. Anyway, back to the topic on hand...we print a lot of sheet stickers...

The lease for our Konica C3070 is up in October and I've given the lease company our 3 months notice that we don't wish to continue the lease. Our aim instead is to purchase the title from Konica as we've done less than 200,000 prints on the machine so it's still a baby (we tend to print higher...

Sorry, I meant flicking the switch on the Duplo itself. I’ve not got a circuit without anything connected, without unplugging the workshop PC’s etc, but will spend some time over the weekend trying it on its own circuit. After today though, I am leaning towards it being a case of catching on...

I’ve got a Duplo DC-445 that I use solely for creasing 350gsm greeting cards. It’s my favourite machine in our entire business as it just works, no faffing, just does what it should. However, it has developed a fault where when it starts the process of lifting the input bed to start feeding...

Hey all. I was just wondering if anyone could offer recommendations for a folding machine that I may be able to find used. Are the older Morgana Juniors any good? We don’t do a tonne of folding so I’m not wanting to spend loads but at the same time I need something that’s going to be accurate...

Have just tried that as well and no improvement :(

I have printed 100% cyan, magenta, yellow and black sheets today and this issue is only appearing on magenta. I’ve also swapped the magenta drum out for a brand new one (again) and still getting the issue. Also cleaned the ROS windows and still no improvement.

It runs from leading edge to trail edge.

Thanks for the suggestions. I would have to look up how to check all of that haha but will have a look tomorrow and post back :)

I’m a Konica fan but recently bought a Versant 80 as a cheap(ish) second machine and have no idea how to troubleshoot it haha. Printing some greeting cards and getting this banding on pink and purple. On a Konica I’d say it’s the corona wires but don’t know if it’s just the drum on the Xerox...

I had hoped that one of the cables was loose and that it'd be a simple fix but turned out to be a dead power supply.

We had the tech out yesterday and he was of the same opinion as your tech that one of the two low voltage power supplies had failed. He's took the first one away with him to test on his machine (apparently the second one is more difficult to get to so he didn't want to take it out if it wasn't...

I left the machine overnight and did as you suggested this morning but still no joy. I've had a reply from the company I purchased the printer from (who the maintenance contract is with) and they are going to send an engineer out. Not a good start though haha.

Thanks, I shall give this a go

I’ve sent them the video but was hoping it’d be something simple that I could fix to get me up and running.

It is on a service contract, yes.

Anyone with a Versant 80 experienced all the lights flashing on and off? We only had this installed on Thursday, left it over the weekend then came in today to this. Have tried powering it off at the wall and leaving it for a few minutes but just reverts to the same state when I power it back...

Hi Halmac, Our plates don't have skew adjustment on them I don't think as it's all done digitally. There's a roller tilt lever which, according to the manual, is meant to fix skew but the paper is still skewed regardless of where that lever is positioned. I definitely think the company I bought...

Just thought it worth mentioning, I've just ran a few sheets through my Duplo DC-445 creaser and they've creased 100% square. I've also just measured the backstop of the guillotine all the way across and that is straight (I did have my doubts haha). So, it's something with the Morgana. I've...

Hey. Thanks for the input. I've checked the paper and it's definitely cut square. I've even tried with uncut paper straight out of the packet and it's still skewed. What I think you're mistaking for cracking is something I've only just spotted but it's on the opening edge of the leaflet, not...