Search results

  1. N

    Problem with Kodak magnus 400 Q

    That transporter failure could have been just caused by repeated power on/off. Could have been a failed firmware upgrade as well - it means the head does not communicate with the MCE board. If it does not go away with power cycles, try upgrading the firmware on the laser to at least version...
  2. N

    Problem with Kodak magnus 400 Q

    That is not banding. Replace hotlink and data cables.
  3. N

    problem initializing carriage motor thermoflex wide l kodak

    Clean the encoder disk thoroughly. If that does not fix it you will need a new drum amp or motor.
  4. N

    Help_Kodak_Magnus 800

    No way to fix it - you will need another laser
  5. N

    Help_Kodak_Magnus 800

    the laser is the issue but not the focus - that is a 3.3v internal converter error If your lucky, it could just be the cable There is no Local 3 card in a Magnus 800.
  6. N

    Lotem 1, Slammer 0

    Turn it off with the doors open. While off - flip the breakers at the back off/on. Turn it back on, then close the doors - always from the middle. The buzzer starts when the sensors are not tripped at the same time while closing the door. It could be a bad interlock board but also misaligned...
  7. N

    problem initializing carriage motor thermoflex wide l kodak

    The problem is not the carriage It is the Z-stage - that moves the laser towards the drum >>stage >>stage init Do not play with all the commands you see with help - running stage install tfx will reset your values in set al and you will never get it running again without somebody qualified. The...
  8. N

    Lotem Drum Housing Material

    aluminum
  9. N

    Creo lotem 400 quantum boot up problem

    That error had nothing to do with TMCE - you most probably made things worse and you may have the wrong firmware or missing nvs parameters now. wincore.cpp is from Windows itself or either corrupted OS or called incorrectly due to a corruption in application - should have reloaded BIOS, the OS...
  10. N

    Kodak Quantum III 400_Problem

    Assuming punches are registered, you will need an engineer to look at your machine. Each plate type needs specific parameters adjusted in the laser - in your case the reflectivity may need adjustment. It is not a sensor - it is a laser beam supposed to detect the plate and track the plate...
  11. N

    Print Console on another workstation

    I guess you meant 2.7 but does not quite work that way... You need proper SCSI card with proper drivers and the CTP firmware needs to match the rest of the software..
  12. N

    Service manual for kodak trendsetter news

    There is no such thing as a service manual for any Kodak CTP be it Lotem, Trendsetter, Magnus, etc... be careful about sharing your emails and what you download... There were some internal websites with lots of information (TechPlanet) that could be available on DVD's which are at least 5-6...
  13. N

    Kodak XPO software

    2003 server x86
  14. N

    Kodak Trendsetter II HELP!!!

    Your problem is the PC controller - not with the Trendsetter - "power saving mode" is a message from the display itself meaning that there is no video signal. Have your computer guy look at it or call Dell for support using the TAG number.
  15. N

    Gave An Employee A Raise , He Turned It Down ...WTF

    you guys are too worn out by the system.... As a well prepared and hard working person I would have personally done the same and refuse an insulting raise plus seriously thinking of finding another job. It simply does not matter what your "policy" is. Don't treat people like slaves or tools...
  16. N

    Looking for a part number for Magnus 400

    298g9l801a
  17. N

    hey guys please any one help me Loader Local

    If you suspect the problem is on the computer side: 1. Make a backup of your Lotem registry 2. First reload BIOS - you should have a floppy or a CD with the BIOS image - com ports settings might have been corrupted - check if problem is fixed - if not go to step 3 3. Install the operating...
  18. N

    problem whit vertical lines on LOTEM 400v!!! HELP!!!

    Beam balanicing refers to a Thermal Laser Head - the Lotem 400V has individual diodes and fibers. If you have problems with beam balancing on a Lotem 800 II (which is a Quantum with Thermal head) contact Kodak or someone who repairs Creo laser heads.
  19. N

    problem whit vertical lines on LOTEM 400v!!! HELP!!!

    this is Lotem 400v - fiber - no beam balance - looks like diodes misfiring - probably DDB card gone
  20. N

    Lotem 800V Motor Drum won't stop fast enough.

    As far as I know this cannot be done - it is not a simple timeout - it is about the drum motor reaching a certain speed in a certain amount of time by applying the correct current, voltage, slip rate control following a predefined algorithm.

PressWise

A 30-day Fix for Managed Chaos

As any print professional knows, printing can be managed chaos. Software that solves multiple problems and provides measurable and monetizable value has a direct impact on the bottom-line.

“We reduced order entry costs by about 40%.” Significant savings in a shop that turns about 500 jobs a month.


Learn how…….

 
Back
Top