Search results

There are dip switches that accomplish the same thing as the jumper. They are very small and easy to miss on the main board. I will try to find my notes tomorrow one of those just probably needs to be changed. But you can take a picture of the working one and set the other one like that should...

I actually have an extra manual pick a lift and auto ejector stacker if you are interested.

Just a thought, How much gripper do you have on the actual printed sheet? If you have a lot of ink coverage close the edge it can cause problems on thin stock. Try running with at least .25” margin.

If you don't see a usb slot on the front of the machine, pry off a little door on the front of the machine, should be a usb slot there. Plug in a usb drive, then choose scan on the display of the machine and you can save it to the Usb. No networking, fiery, or software required.

Does anyone know what this kind of padding is called? Or what is involved to make it. This particular one has a hexagon finish to it, but I have another one that looks more like linen. It is much stronger than regular padding glue and flexes more like a perfect bind glue.

We’ve been using them for a few years, so you have any specific questions?

both are sold

Why don’t you export your file as a pdf, you should be able to import that file directly into the rip to make the plate. This bypasses having to setup the rip as a printer. Much easier.

my guess is something is messed up in your profile. Does it print fine on 12 or 16pt? Try using that profile, or start a new one from scratch without using the media import and see if that works

We have a heidelberg Printmaster 46-2 for sale + Mitsubishi SDP-Eco 1630 IIIR – Platesetting System w Harlequin Rip. + Press Specialties C9000 Envelope Feeder + Conveyor + challenge jf paper drill Good working condition. $4000 takes it all. Located in Los Angeles.

I had a very similar issue about two years ago. I think ours ended up being on the non operator side there are a bunch of small air hoses near the top that actuate the rollers. Take that panel off and see if you can feel any air leaking over there. Also check that you are not leaking anything...

Yes, they are docucopy with the trilar coating. I did try adjusting the trailing edge transfer, didn't help. When they work the copy is razor sharp and fusing well, but a fair number of them have major flaws that make the set un sellable. It seems like an issue in toner transfer to the sheet...

Is anyone able to print on Mylar tabs on their Ricoh 9200 or 7200? We can get them to feed fine but the type looks terrible on 15-20% of them towards the edge of the tab, bleeding Flaws that move around, not in the same tab every time. Using the trilar tab profile imported from the library. We...

For the hot lam get an adhesive eraser xyron makes a cheap one and a lot is elbow grease will clean it right up. Let it warm up a little but not hot will also help. A rag and solvent also does it but a lot more work.

I have one, works great, very few problems. WAY better than trying to do those laser plates, especially if you need good looking screens or longer runs.

Make sure the hollow center of the drill is clear, if not clean it out with a nail and also replace the round wood block you drill into. If all else fails put a few pieces of chip board under your job.

Has anyone purchased a Ricoh from cbe or impact in Los angles? I like the product but am weary of their service claims vs Ricoh direct.

I had the exact same issue with an older xerox docucolor, it ended up being a patch was needed for the fiery. It took forever for them to diagnose, and if they ever reset the software I needed to go back an apply that patch. Try bugging phone support until they get you to Someone higher up.

Thanks! yes, obvious now, but I didn't know what it was called.

Am I able to rasterize a pdf in pitstop 2017? I don't see it anywhere. I frequently have large pdfs with lots of powerpoint slides that crash in the rip if I don't rasterize the problem pages in acrobat or photoshop and bring them back in.