Search results

Is there any specific reason why you're after consumables for a different model? TN-616 and DV-617 are for C6000/7000.

Did you ask your tech about this? :) Try to clean/replace your paper feed rollers. This may cause such a behavior. Next thing is to change dipSW 11-3 to 1 (Automatic restart at “Press START to restart” situation after releasing jam.) dipSW 11-6 to 1 (Automatic paper supply) Good luck.

Your techs are absolutely right it is the low humidity that causes this. Try lowering the 1st transfer values for Yellow and Magenta to -2 or even -3 [03 Administrator Setting] -> [01 System Setting] -> [05 Expert Adjustment] -> [06 Process Adjustment] -> [01 Front & Back Density] After the...

No, I don't mean Auto gamma offset adjustment. Neither Auto gamma adjustment. I meant Printer Gamma Offset Adj. also called Printer Gamma Offset Adj. Manual. Download Gamma offset.pdf This adjustment has to be done for each screen (or at least for the one you use, probably Dot1). Like I wrote...

Hey my friend, did you ask your tech about that problem? To me it looks like Gamma offset on your machine is way out. Perform Gamma offset adjustment then do calibration and the problem should disappear. If you don't know what I'm talking about, ask your tech. Cheers. Let me know with the...

Try this [Subject] "Warming up. Please wait." message [Description] The control panel periodically indicates "Warming up. Please wait." There is a delay of up to two minutes between jobs. [Solution] CAUSE: Incorrect setting. SOLUTION: Change soft switches 5-0, 5-1 and 5-2 to ON...

I have done that in the past. Results were great and especially for this problem. You can use DC5000 dev unit also but the doctor blade gap is too much for DC252 and needs to be adjusted.

Tell them to change the ROS (which is the laser unit), dev unit and 1 btr rollers at the same time. Then you will notice improvement. I know that they won't listen, but tell them to change the dev unit with dev unit for X700, it will do much better. Good luck.

Check here, Error Code KM C6500 Magenta shifting

[Subject] "Warming up. Please wait." message [Description] The control panel periodically indicates "Warming up. Please wait." There is a delay of up to two minutes between jobs. [Solution] CAUSE: Incorrect setting. SOLUTION: Change the setting of Fusing Stability (Tray switching time)...

Utility - Admin - Common Setting- next - next - Double feed sensor 'off'

How about the 1st transfer rollers? Have replaced them? Try playing with 1st transfer current: [Utility/Counter] => [03 Machine Admin. Setting] => [01System Setting] => [05 Expert Adjustment]=> [06 Process Adjustment] => [01 Front & Back Density]

If you change the lamps it will cause the fuser to heat up more slowly . And and error code may appear. Don't try it.

I had this in the past. 100% it's the cable between the creo and engine. You can try cleaning the contacts, but better replace it.

I can't believe it! X700 is great machine, but C7000 is also great. Can you please tell me which configuration you have C7000 with PF-602 or LU-202?

Temperature 18-23 °C Humidity 40-60 %RH

No don't change it. Yes you are right it only changes the nip. Like I wrote in my first post: Larger value means lower nip pressure（fix level down/Side Gloss less）. Smaller value means higher nip pressure（fix level up/Side Gloss worse） If you set it to 10 (Non half latch) for this...

Ooh man where are you. I didn't realize that you were the one with registration problem on C6000. I think that you are unlucky with techs :) C6000 has much better registration then 700 or can be achieved. Did your tech try the suggestion that I've provided in your other post? sykomac Any...

The NVMs that I've provided to you can't be changed from admin mode, you can change them ONLY from service mode. Ask your tech or try it by your self (it won't hurt). Hold "0" five secs and then while holding it press "start" you will be asked for pass. enter "6789" then go to machine status...

740 - 043 to 1 This will activate "fuser gloss mode" for paper 177gsm and upper. CanarcticPress Your tech is wrong, by activating it, actually you reduce the 2nd transfer 100% to 70% and by this less toner is laid on paper. Fuser temp is increased by 17 degrees . "machine speed" for 177gsm and...