Recent content by STW100

15-08 is a braking issue! Meaning the press is not stopping quite perfect for the software. Poss need to tighten the belts. If you are rec other strang 15-0? codes, check the roll pin in the main dr gear at the impression cylinder! Stan ipsqm46.com

Rob, I carry shop towels, LT blue 100% cotton, approx 16"x24", could be washed but sell as disposible. I sell quite a few of these, customers tell me it is cheaper than a towel service! 25lb box $77.21 + shipping(approx 75 qty) ipsqm46.com

SF45 is total impressions based on software! 18,267,241 My guess it has been updated or the ZTK board was changed out. Either way, the mech should have set the proper count at that time. SF41 is press revolutions. Most likley 2x the impression count. If you have any questions feel free to give...

Is the top guard setting flat? Does the top guard bounce during eject? If you are still having issues, give me a call and I will be happy to give you some suggestions! Stan, Intermountain Press Service 720-285-9485 ipsqm46.com PS: I have numerous new & used parts avail for...

What unit are you talking about? PU-1 , PU-2 or both? What is contacting the cylinder all the time? The rubber drive wheels or the plastic wheels? Stan ipsqm46.com 720-285-9485 PS: I have numerous new and used parts for your press!

I do carry rollers! I have the OEM Bottcher & ARC rollers. Give me a call and I'll be happy to quote you a set and also confirm the setting of the rollers. Usually you run out of adj on the ink forms 1st not the transfers, but being 5 years old who knows! Stan ipsqm46.com 720-285-9485

Just for your information, the red screws are for the 3rd form to dist roller! 1st form to dist / yellow screw, 2nd form to dist / blue screw, 3rd form to dist / red screw 1st form to plt / orange screw, 2nd form to plt / pink screw, 3rd form to plt / painted silver screw Note: all form adj are...

I am parting out a Heidelberg Quicksetter QP-350 and also have some new gears available for same.

What is your deep cleaning process and time frame? Meaning do you ever use Feboclean & Calciumfix? How often? I'm not real familar with Komoris but I am a Bottcher dist and would be happy to get you a roller quote. Stan, Intermountain Press Service, llc. ipsqm46.com

That damp unit was used for a short time and I believe there is no adj for the damp dist to form roller. I am supprised that you would have a 5mm stripe, usually the issue is little to no stripe. The damp dist roller shaft is flat on 3 sides & round on the 4th, the 4th side should be up. I would...

The red screws are next to the side frame under the plate cylinder shaft. You access the screw from the damp side of the cylinder. If you still need some info please give me a call I will be happy to help. Stan Intermountain Press Service,llc. 720-285-9485 ipsqm46.com PS. I also have...

The only place the 3/2 way valve can get dirty is from the sucker bar. Most common reason is a dull knife on trimmed stock. When you clean and grease, you shoul be using a silicone grease and very little of it. You should be hardly able to tell if you put any on the piston rings or not. Stan...

I have the rollers you need based on your ser# 960030. Is all I can think is they had a roller boxed wrong or a def shaft. I have a few new & used shafts also. All rollers are press ready, except PU-1 distributor up to ser#960331. I have a few new parts & numerous used parts availble. Stan...

I can help you with your roller questions. I carry Bottcher rollers. Unless you have one of the first QM46,s I am not sure what the roller issue is. Give me a call. Stan Intermountain Press Service,llc. 720-285-9485 ipsqm46.com

check ipsqm46.com