Search results

I have this error 139 Cannot switch K4 to Master Mode. Also I noticed I don´t have any signal from SDM Board for example I leave the covers of the drum open and the Av didn´t stop the spin motor start, no error 13, before of 139 the error was 13 with the covers closed. I already check the sdm...

It´s possible the DEC board NOT supply voltage to the boards SDM, etc. . How can I check the voltage for SDM board from DEC.

I check the DEC board in another working Avantra and the same error (13) appear, that´s why I am very sure the conectors, cables, from SDM are ok, the only possibility about conectors is the conector pins on the DEC board tomorrow I going to check it with a Magnifier glass. It´s a possibility...

service this AV44 long time ago, No I didn´t replace anytime DEC or SDM, neither any software upgrade. I have to check the version of SDM FPGA. But I know for sure is the original working several years with same board. I remember this problem appear after I try to correct some problems with the...

I have an error 13 (left door open) on AV44. I already check the switch is OK, cables, conector to SDM Board everything is OK, even I check with another SDM Board and the error still . I check disconecting the cable from DEC to SDM the error 13 still the same. I suspect the problem is with my...

José Carlos: Please explian what you did to CPU board Luis Avila

overexposure

I have a AV44S with registration problems, also it have a overimage (20% goes to 90% or more) like the film is not complete adhered to the drum but only a wrinkled. I check vacum line it´s ok 13 in/hg, the suction on the film a seems ok:confused:

Did you replace Capacitor Only wich one? I try to search your complete solution but is not any more.

Yes I did, do you know where I can find one of those or what can I use to replace it, also If you can tell me a tip how to put the heavy punch assembly without damage the rubber seal. Thanks a lot for your care and help.

the problem is lost of register, I don´t get any error message. I was causing this problem because I removed the punches to avoid film jam because every time I load or reload film the error 6 appears and the film jams in the punch system.

:confused:I have lost of vacum, I already check the vacum pump alone is 15 with the vacum system connected drops to 2, I replace all the hoses but I saw the problem is between the punch assembly and drum is a rubber gasket but I cant find the original replacement somebody have the exact size of...

I want to buy a Galileo VE the people who offer this CTP told me this model (2005) have a 60mW laser to expose Violet Photopolymer plates because I want this kind of plates, the question is can I use the LP-82 Processor, do I have to do any changes to the processor. Also I want to use a FUJI...

I had the same error a month ago in my AV44S, I had cleaning, lubricating many times, etc. the problem disapear for a few days only. Finally I replaced the carriage board on AV44S and everything is working ok now

I have problems with the bridge of my AV30, because the film goes to fast to the processor and sometimes the film jam just betewn the bridge and processor input and every time the film practically hits with the first rollers of processor input. I tried to use a AVDIAG to control the speed or get...

Sorry I am new using AVDIAG ? How I declare Bridge board Installed ? I sent my diskette to the people who sold me the DEC to they restore the parameters of the new DEC, but they say is not very important.... :( Now I have to adjust BOL (I know how) what else do I have to adjust? if I don´t get...

I had an AV30 on service, with a DEC board failed to boot. I got an used DEC board, now the machine boots ok, but when I try to film error 41 appears (bridge not in possition) but I´m sure bridge is in possition very lowered . Then I run the AVDIAG to check the sensors, but in the first screen...