Search results

We change the old TSP board for a fully functional TSP (tested) and problem solved . Very sad That nobody wants to Contribute something in this forum.

We have changed TSP Board TSP Cable Network Cable Power distribution board Sending another job Still the same Any suggest?

Few days ago the exposition of a plate got stuck on 80% and did not advance without throwing any error. Now, the exposition got stuck on 0%. No error appear. The motor carriage is stuck on a loop during exposing. But it moves correctly during testing. In the card strobe7 the LED STPRL blinks...

I want to share the solution to this problem. A sensor of the motor carriage, in the right part, was changed . A DDL card (The laser controller card), the number 0, was changed . The technical service informed us that the diode 0 is the one responsible for the edge detection. I hope this...

Hi. Working with Lotem 400 . The first exposition of the plate is correct. In the second exposition this error appear: "Edge detected beyond the begining of the plate". Some problems with laser appear too. Reset the machine and again have success with the first one. The second can not be...

Thanks Les, indeed the problem of laser was due to poor conditions in the environment. Required to be colder. For the image exposure problems, the TSP card was causing problems, it was necessary to clean the slots that are inserted into the PCI port with an eraser and that solved it . Thanks...

Hi. After exposing a plate on Lotem 400 i'm getting a image like ghosty. A week ago we change three LDD2 Laser Driver Board from old Lotem 400 system since we get this message "Performance reduce to non-working lasers 21 (3-23) of 24 are working". This problem was gone after that. But now...

Hello, Good morning A problem has arisen with my system CREO Lotem 400 Message: Communication problem: The output device doesn't fetch/ndata. Please check the output device. Error 684. Everything turns on normally, place the plate and sent the job. After a while this error comes and goes...

About this problem, a colleague told us that can be the TSP board. A test we did was disconnect the TSP board. The problem continued. And connecting it, it also came out the same error. Do you think it is this card? It looks that way. We do not have any to try. Any other ideas? Thank you a...

When posting a job, after a few minutes, the job is aborted and get this error: Communication problem: The output device doesn't fetch/ndata. Please check the output device. Error 684. No progress in the exposition, just does not do the job. Any idea what is causing the problem? There has...

The lotem interlock2 board may not be working. This card is located in a box behind the main switches. That was our solution.

Since i tried to figure out wich is the MCF card, i tested all the boards. I get 5.10 so did not need to adjust the PSU. But on one side of the top card i didn't get any lecture (img1). This mean something? Also i tested the PSU. (Img2). I'll be pleased for more information. Thanx on advance.

¿Do you Know what is causing?

Nothing crazy but yes, after checking with my supplier (because i didn't recieve the manual or drivers). It turn to be the power connectors of the board. Thanx a lot. Now i have video, but this problems shown: 2 Open interlocks Motor interlock defeater Thermal Head Focus defeater Local 3...

Hello I have this Lotem 400V who was not giving video signal on the cpu board. After several testings we determine that the problem was the cpu board, so we replaced with a new one, but is giving the same problem. We changed the power supply and the power card. Check all the fuses. What...

Hello Kevin. I sent you an email for support. Thank you for your reply.

Does not start, no video signal after pressing the yellow buttons in the back of the lotem 400. Is not a pc like we know, is an old pc card system. picture: http://picturepush.com/public/6836321

I have a Lotem 400V year 2005 manual loading. This worked for me: Change interlock card - Located behind the door of the box where the main switches are located The white switch of the box located inside the left door is down (000) move it up (111) goo luck.

LoWang, you mean the lithium battery at the standard controller? seems to been atached to the card. :( No luck so far. I'm trying with a PCI vga video card into a free pci port.

I tested with another power supply and RAM memory but still no video signal The Num Lock key on the keyboard seems to work The door alarm works when i left open. Before this problem the yellow buttons were not working properly, had had to push several times to start the application. Any other...