Search results

ERROR 8303 The temperature monitoring of the optics unit reconigzed an error

1 bit tiff license 1 bit tiff license I´m using harlequin. Finally I have to reload the system from NT but I did it in another hard disk. I am connected again:D But now I have a problem with 1 BIT TIFF License. I don´t how to get it from the old hard disk and pass to the new one. Regards...

I have a problem the Plotter don´t connect to the RIP I already replace TSP Board, cable to the plotter. The producction manager window doesn´t show... Diagnostics doesn´t show any error. Regards Luis

I need help on this problem, Producction Manager window doesn´t show LotemCalib window also doesn´t show and I get the error Can´t connect to plotter I run all the diagnostics test and NO errors Also I check the laser group and all the 24 laser are ok Also I reload the Xpose software...

Alekbelia, I have the same problem with my lotem 400 manual loading, how do you bending the input rollers, do you know if exist some adjustment to do that. Regards, Luis

Check the temperature. The oldest Avantras need more cold. I solved many irrational problems, lowering the temperature to 19 Celsius

I have an ECRM 56 with registration problems, do you recomend change the capstan motor or it and be adjusted the film drive system.

Hello everyone!!! Somebody knows what is going on with error 82 Unknown bridge error. this error appears when I try lift the bridge with the OCP command. Also when I run SRAM bridge test with AVDIAG, but sometimes is passed. I already check lift motor, sensors, cables in the bridge, also I...

Hello friends, somebody update a Avantra 44 to 44S, I think is possible changing the DEC and Spinner. Somebody did it? What do you think are the implications to being succesfull?

Maxon, thank you for your interest. I´m service other imagesetters Agfa Avantra, Linotronic, Herkules. My experience is almost 20 years since 1994. But not in MAKO is too few around and is not possible to get a trained ECRM engineer around. So that´s why I replace the main board for a used one...

I have a problems with a ECRM Mako 56 System Error 3 appears frecuently. Also sometimes system error 2 I just replace the main board because in the display appears only black squares with any error information. Now I have all the functions back everything is ok even the film output is ok the...

Thank you I like your proposal, honestly the problem started with 154 Error DSP Handshake failed, that´s why I try to downloading the DSP FlashROM with AVDIAG I´m not a expert engineer but I know how to use AVDIAG and I know is not a playing game. I fix Avantras here in my city Guadalajara...

Ok Armya, can I send you the DEC so you can try to fix it, do you know the cost aproximately.

Thank you STSTech, do you think is possible to reload the DSP software?, where I can get it?. Can I saved from other working AV44 and downloading to the bad one?. What do yo think about the first error 154 is possible the DEC was already bad?

I have problem with AGFA Avantra 44S > > Error 154 Diag to DSP Handshake Failed, after that become many errors > codes. > > I try to fix it with AVDIAG RELOADING DSP FlashROM but now in the boot > just before the DSP test appears FF.FF.FF then error 140 DSP H/W HandShake > Error. > > Can...

Positive it´s a DEC board problem, I resolved cooling down the DEC, sometimes the lines appear again but much, much less one line only but most of the times didn´t affect the job. Thanks for your help

so, do you think is the laser unit, I never saw before a laser to fail in Avantra

I have a problem with AV30, boots with no errors at all. but the output print becomes with hair lines in fastscan direction. First I resolve the problem cooling down the AV (19 C) But now the problem start again. I think is a DEC failure may be in the buffer RAM I think.....:confused:

I have a problem with a Herkules, during film loading error 350B Controller Material.:(

I have another AV44S I try with another DEC and boot ok, now I have error 82 (unknow bridge error) when I try the function to open up the bridge, also I have error 70 (buffer error) do you think is a parameters problem because I didn´t know how to get the parameters of the faulty DEC board and...