Search results

The problem was solved after placing the DCU SIMM as follows:- D1 D2 S1 D3 S2 D4 S3 D5 D6 S4 S5 S6 S7 S8

Please Suggest me. I will be ever grateful.

Dear Sir, I am in a trouble with my Screen SG-8060P Mark II Digital Drum Scanner. At the time of scanning it is showing Error massage:- S-S72F1 : Scanner Error occurred. DCU # 1 illegal DCU is inserted. I have opened all the 14 DCU SIMM and replaced after cleaning. Now it is showing Error...

Dear Zombie, I am in need of Service manual for kodak trendsetter. If you can give it to me I will be ever grateful. My E-mail Address is ([email protected]; [email protected])

Dear Sir, I am in a trouble with SCREEN Platerite HD8900. If anybody suggest me about this matter I will be ever grateful.

Dear Sir, I am in a trouble with my Screen SG-8060P Mark II Digital Drum Scanner. Sometimes the scanned image is very fine and sometimes horizontal stripes/ lines on the scanned image. I have replaced the Xenon Lamp with a new one. But the problem is same. Please advice about the problem and...

Dear Sir, I am in need of Control System Software for HMI and PLC along with driver folder for Inca85T CTP Processor. I am in trouble with the Software. If anybody help me with the Software I will be ever grateful. Moreover I need Delta VFD004E21A Inverter setting Data for Inca85T CTP Processor.

Dear Sir, I am in a trouble with my ECRM Stingray 52/63 ImageSetter. When I Expose a job Solid Film ( Complete Black ) comes out. But spaces between 2 Exposes are clear White. If I auto cut the Film the total un Exposed films are clear white. Only the Exposed Area becomes Solid / Black. But no...

Dear Sir, Thank you for your reply with suggestion. These scratches are not form the rubber roller of Plate loading section. It's look like Vertical Scam. After Processing Vertical Scams are on the CTP Plate. But if I Re-Process the Plate with the Processor then the Vertical Scams becomes more...

Dear Sir, I am in a trouble with SCREEN Platerite HD8900 CTP Machine. When I output a job there is a lot of Scratch on the CTP Plate but no Error Message on the display. I have checked all of the CTP Plate Loading & Transport section. Moreover Exposing from HD8900 I have processed the CTP Plate...

Dear Bast, Thank you for your reply. The Problem has solved after replacing the SCSI Card of the PC. Before it was Adeptec 2940UW. Now it is working with Adeptec 2944UW. Do you please suggest me about how to replace the SCSI card instead of Adeptec 2944UW. I want to use another SCSI Cards...

Dear Sir, I am in a trouble with ECRM Stingray 52/63 Imagesetter. When I output a job from the RIP, it shows " %% Failure opening SCSiPel driver. %% Imager not found on SCSI bus. Powered off ? Not connected ? " on the RIP. I am using RIP 6.4 version. I have already replaced SCSI Card of the PC...

Dear Sir, I am in a trouble with my PCI SCSI card used with operating PC of Fuji Luxel F 9000 Image Setter. The original Card was LSI Logic (Symbios) LSI 8751D. It is not available in Bangladesh. I replace it with Adaptec PCI Ultra 2944UW. It is working but very slow data transmission. Anybody...

Today I have replaced the defective Control Board of Fuji F9000 after cleaning with Isopropanol. The scratches of the film has gone but a new problem arises. Some times data transfer has done correctly and sometimes data transfer hangout without showing any Error Massage. Please give me a...

Dear Sir, I have no Service Manual. Previously I was related with Photographic Minilab for 10 years. Now I am related with Pre-Press Image Setters and CTP Machineries for the last 3 years. I am repairing the Electronic Circuit Boards from my basic idea. If you can help me with some Service...

Dear Sir, I am in a trouble with LUXEL F-9000 Image Setter. When I output a job there is a lot of Scratch on the Film but no Error Message on the display. I have checked all of the Film Loading & Transport section. I am sure that the problem is from the Electronic Boards. I attached a test Film...

Dear Sir, I am in a trouble with Screen Platerite HD 8900. When I start the Machine it works smoothly. But after an hour it shows Error Message E001002: Mechanical Error. ( Nip roller does not descend). If I clean the M53 Motor and LBS Sensor, it works smoothly for another hour. But after...

Dear Maxon, When I transfer a Job the problem arises. I think the Terminator may be defective. It is possible ? Please advice. There is no Error Massage on the Display.

Dear Maxon, Thank you for your prompt reply. I have loaded Film several times into my 2 cassette and cleaned input rollers and dancer steel bar so many times. But no result. Same problem occurs again and again. Please advice.

Dear Sir, I have an ECRM Stingray 63 Imagesetter. When I output a job it shows " RECORDING IMAGE FILM COUNT" and count up 10% to 20%. But after count up 10% to 20% it becomes hangout and Film automatically returns to the cassette. There is no Error Message on the Display and without restarting...