Search results

68Shelby, I can help with your issue, please contact me directly to discuss.

gtmo, Who did you purchase the RIP from? They should have installed the HQ RIP and trained you. Not only would it do what you needed when they left, but you would have an understanding of how to make changes if necessary. If needed, this can be provided remotely.

egorus, the "air bearings" are actually Teflon pads that separate as the motor spins up creating a cushion of air for the motor as well as provide for braking when the motor spins down. I would not attempt to do anything with it yourself. You should look for someone who is qualified to work on...

You guys are killing me..... The optics are dirty, it's a very common issue. Just be careful not to scratch the mirror or lens.........

MOhamad MOhamad From reading all of the post it seems there's a confusion of your problem. I'm going to go a different direction and as if this is a constant problem or intermittent. When you say it does nothing, does it advance the film and act like it's doing everything properly but just...

Vlad, We usually agree but not in this case. As someone who sells and maintains all of the different CTP technologies, the iCTP definitely has its place. The registration is no issue and if properly maintained as recommended, which is very simple, the iCTP runs with no problems at all.

What a shameful way to advertise.... Infrared Lasers have not been used in Imagesetters for at least 15 years and with the reduction of film manufacturing in general what IR film that is left is going to diminish very fast. My point should have been: The system is so old that service, parts...

Forget about the 9400. The type of film it uses is not manufactured anymore.

Xitron supports the QMDI. You can contact them directly or thru a dealer. We can take care of this if you cannot find anyone in your immediate area.

Vlads comments are not out of line. If you cannot figure out something so simple by looking at it, then hire someone who can. The part you are referring to was a mod. kit and is not covered in the service manual.

JSM, It seems your question was not understood by all. Since your RIP is on a Mac, it will be fairly simple for you. You don't have to add anything to the RIP because Hot Folders are already there as an input option. If you have an IT guy for your Macs, all you have to do is communicate...

sistecopy, You can either go to Xitron's web site or purchase it through an authorized dealer. The cost will be the same. Also, the Blue Box is probably all you will be able to purchase new.

macdesign, These are two different issues and one cannot cause the other. If you still require the AV30 for business you need to seek out professional help for repairs.

Idriftfish, Sorry to be so long in checking the forum. There are 2 different AV30 OLP's and both of them can run Poly without any trouble. Where are you located and whom so you deal with for your consumables and service?

Harperprinter If your positive the boards are all good, it is most likely the input jam sensor. I have this available if you would like to contact me directly.

How do you have the trapping set up? Is the black set to overprint in Quark? Try setting the trapping in the RIP to Auto and you will get the best results for most everything you output.

Depending on which CTP you are using will also depend on how much the exposure level will change as much as the plate manufacturer. Also, each system is going to be slightly different. You need to test out your system and definitely use the Analog wedge for your test. The laser Has To go...

Increase your exposure setting. If this does not help, you need a a new laser and or laser power supply.

Jamie, We are also a dealer for Xitron, that is why I recommended them to you. If you are looking to deal with someone not necessarily in your area, don't know where you are located, we can also help. We also offer remote support for the RIP as well as offer service for the AccuSet 1500.

There a small hidden files left over in the "Spool Folders" that the RIP sees during boot up. If you watch the screen you will see the RIP try to interpret these files and flush them. This is just a normal PC thing and you are doing the correct thing by just saying ok and letting the RIP...